Document Outline

• 1 General
  • 1.1 Information about the user manual
    • 1.1.1 Legend
  • 1.2 Safety
    • 1.2.1 Explosion Proof Housing
  • 1.3 Limit of Liability and Warranty
  • 1.4 Unpacking and Inspection
  • 1.5 Service Request, Repair, or Support
  • 1.6 Shipments to LumaSense for Repair
  • 1.7 Disposal / Decommissioning
• 2 Introduction
  • 2.1 System Overview
  • 2.2 System Features
  • 2.3 Principle of Operation
    • 2.3.1 Alarm Set Point
    • 2.3.2 Relay Contacts
  • 2.4 Signal Path
    • 2.4.1 SM: Smoke Monitor’s Dual Wavelength (2 color)
    • 2.4.2 PM: Pilot Monitor’s Flame Sensitive Wavelength
    • 2.4.3 FM: Flare Monitor’s Flame Sensitive Wavelength
  • 2.5 Quick Installation Procedure
• 3 Mechanical Installation
  • 3.1 Getting Started
  • 3.2 Sight Assessment
    • 3.2.1 Pilot Monitor (PM) Sighting
    • 3.2.2 Flare Monitor (FM) Sighting
    • 3.2.3 Smoke Monitor (SM) Sighting
    • 3.2.4 Mounting Options
  • 3.3 Ambient Temperature Limits
  • 3.4 Cooling Requirements
    • 3.4.1 Water Cooling
    • 3.4.2 Vortex Air Cooling
  • 3.5 Viewport Air Purge Requirements
  • 3.6 Target Size and Focusing Range
  • 3.7 Focusing on the Target (Adjust Lens)
• 4 Electrical Installation
  • 4.1 Electrical Installation Guidelines
    • 4.1.1 Conduit/Connections
    • 4.1.2 Over-Current Protection/Service Switch
  • 4.2 Power Connections
    • 4.2.1 Service Markings
    • 4.2.2 Protective Ground Connection
    • 4.2.3 Cover Attachment
    • 4.2.4 Powering with 115 Volts AC∽
    • 4.2.5 Powering with 220/230 Volts AC∽
    • 4.2.6 Powering with 24 Volts DC
  • 4.3 Fusing
    • 4.3.1 Mains
    • 4.3.2 Heater
  • 4.4 Connection for mA Output
  • 4.5 Connecting the Set Point Relay
• 5 Operating the M8100PM-EXP
  • 5.1 Start-Up Operation Checklist, Pilot Monitor (PM)
    • 5.1.1 Getting Started
    • 5.1.2 Initial Control Settings
    • 5.1.3 Delay Setting
    • 5.1.4 System Gain/Climate Compensation
    • 5.1.5 Oscillation on the Analog Meter
    • 5.1.6 Noise Amplification
    • 5.1.7 Relay Contacts
    • 5.1.8 Delay Adjust
    • 5.1.9 Milliamp Output (+mA / -mA)
• 6 Operating the M8100FM-EXP
  • 6.1 Start-Up Operation Checklist, Flare Monitor (FM)
    • 6.1.1 Getting Started
    • 6.1.2 Initial Control Settings
    • 6.1.3 Delay Setting
    • 6.1.4 System Gain/Climate Compensation
    • 6.1.5 Oscillation on the Analog Meter
    • 6.1.6 Flare Monitor (FM)
    • 6.1.7 Noise Amplification
    • 6.1.8 Relay Contacts
    • 6.1.9 Delay Adjust
    • 6.1.10 Milliamp Output (+mA / -mA)
  • 6.2 Considerations for the Flare Monitor (FM)
• 7 Operating the M8100SM-EXP
  • 7.1 Start-Up Operation Checklist, Smoke Monitor (SM)
    • 7.1.1 Getting Started
    • 7.1.2 Initial Control Settings
    • 7.1.3 System Gain/Climate Compensation
    • 7.1.4 Set-point
    • 7.1.5 Relay Contacts
    • 7.1.6 Delay Adjust
    • 7.1.7 Milliamp Output (+mA / -mA)
    • 7.1.8 Final Steps
  • 7.2 Considerations for the Smoke Monitor
• 8 Troubleshooting
  • 8.1.1 Sight Path and Optical Alignment
    • 8.1.2 Power Input
    • 8.1.3 Power Fuse
    • 8.1.4 Instrument Loops
    • 8.1.5 Stopped Chopper Wheel
    • 8.1.6 Broken Wire Harness
    • 8.1.7 Component Failure
• 9 Maintenance
  • 9.1 General Maintenance
    • 9.1.1 Chopper Motor Repair
  • 9.2 Cleaning the Optics
• 10 Safety Assurances and Precautions
  • 10.1 Hazardous Environment Safety
  • 10.2 Electrical Service Protection
    • 10.2.2 Over-Voltage Protection
    • 10.2.3 Transient Protection
    • 10.2.4 Wiring
    • 10.2.5 Protective Ground Connection
• Appendix A: Specifications and Parameter Settings
• Appendix B: Area Classification/Protection Concepts
  • Label Markings
  • Protection Concepts, Article 500
• Appendix C: Declaration of Conformity/ Certificate
• Appendix D: Statement of Limited Warranty, New Instruments
• Appendix E: Engineering Drawings
• Index