Document Outline

• 1732E-UM002A-EN-E 1732E EtherNet/IP ArmorBlock Supporting Sequence of Events User Manual
  • Important User Information
  • Table of Contents
  • Preface
    • Who Should Use this Manual
    • Purpose of this Manual
    • Common Techniques Used in this Manual
  • Chapter 1 - About 1732E ArmorBlock Modules
    • Overview
    • Module Features
    • Hardware/Software Compatibility
    • Use of the Common Industrial Protocol (CIP)
    • Understand the Producer/Consumer Model
    • Specify the Requested Packet Interval (RPI)
    • Chapter Summary and What’s Next
  • Chapter 2 - Module Overview
    • Overview
    • EtherNet/IP Network Overview
    • Introduction to CIP Sync
      • What is IEEE 1588 PTP (Precision Time Protocol)?
      • CIP Sync Support
      • What is CIP Sync?
      • What is Time Stamping?
    • Introduction to Sequence of Events modules
      • High Performance Sequence of Events Applications in the Logix Architecture
        • First Fault
        • Real Time
      • First Fault Detection
        • Time Stamped I/O
      • High Speed Applications
      • Motion Control
      • Global Position Registration
    • Chapter Summary and What’s Next
  • Chapter 3 - Use the Module in an ArmorBlock System
    • Introduction
    • Differences Between Module and Standard I/O
    • Similar Functionality to Standard ArmorBlock
    • Chapter Summary and What’s Next
  • Chapter 4 - Install Your Module
    • Overview
    • Mount the Module
    • Wire the Module
      • I/O Connectors
      • Ethernet/IP Connectors
      • Auxiliary Power Cable
    • Chapter Summary and What’s Next
  • Chapter 5 - Configure the Module for Your EtherNet/IP Network
    • Introduction
    • Configuration Requirements
      • IP Address
      • Gateway Address
      • Subnet Mask
    • Set the Network Address
    • Use the Rockwell BootP/DHCP Utility
      • Save the Relation List
    • Use DHCP Software to Configure Your Module
    • Chapter Summary and What’s Next
  • Chapter 6 - Configure the Module Using RSLogix 5000
    • Introduction
    • Set Up the Hardware
    • Create the Example Application
    • Configure Your I/O Module
      • RSLogix 5000 Configuration Software
    • Overview of the Configuration Process
    • Add a New Bridge and Module to Your RSLogix 5000 Project
      • Add the Local EtherNet/IP Bridge to the I/O Configuration
      • Add the 1732E-IB16M12SOEDR as a child of the 1756-EN2T module
    • Use the Default Configuration
    • Change the Default Configuration
    • Download Your Configuration
    • Edit Your Configuration
    • Access Module Data in RSLogix 5000
    • Configure RSLogix 5000 and the 1756-EN2T Communication Module for CIP Sync
    • Chapter Summary and What’s Next
  • Chapter 7 - Module Features
    • Introduction
    • Determine Module Compatibility
    • Module Features That Can Be Configured
      • Operational Mode
        • Per Point Mode
      • Timestamp Capture
      • Timestamp Latching
      • Input Diagnostics
        • Short Circuit Protection
        • Open Wire Detection
      • Software Configurable Input Filters
      • Communications Format
      • Electronic Keying
      • Module Inhibiting
      • Module Fault Reporting
      • Fully Software Configurable
      • Producer/Consumer Model
      • Status Indicator Information
      • Agency Certifications
    • Chapter Summary and What’s Next
  • Chapter 8 - Using the Module
    • Introduction
    • Overview
    • How Does the Module Store Timestamp Data?
      • Using Timestamp Latching
      • Using Timestamp Capture
    • Manage the Data
      • Module Sends Data to the Controller
      • Copy Relevant Input Data to a Separate Data Structure
      • Acknowledge Timestamp Latching Timestamp Data
    • Sort the Data
    • Clear All Data From the Module’s Buffer At Once
    • Propagate a Signal From Input Pin to EtherNet
    • Chapter Summary and What’s Next
  • Chapter 9 - Interpret Status Indicators
    • Introduction
    • Chapter Summary and What’s Next
  • Chapter 10 - Troubleshoot the Module
    • Introduction
    • Troubleshoot the Module
      • Determining Fault Type
  • Appendix A - ArmorBlock 2 Port Ethernet Module Specifications
    • Specifications
  • Appendix B - Module Tags
    • Fault and Status Reporting Between the Module and Controllers
    • Module Tag Names and Definitions
      • Tags Used
        • Configuration Tags
        • Input Tags
        • Output Tags
  • Appendix C - 1732E EtherNet/IP ArmorBlock Supporting Sequence of Events Data Tables
    • Communicate with Your Module
  • Appendix D - Connect to Networks via Ethernet Interface
    • ArmorBlock Module and Ethernet Communication
    • ArmorBlock module and PC Connections to the Ethernet Network
      • Ethernet Network Topology
      • Connecting to an Ethernet Network
      • Cables
    • Ethernet Connections
    • Duplicate IP address Detection
    • Configure Ethernet Communications on the ArmorBlock module
    • Configure Using RSLogix 5000 Software
    • Configure Using Web Server
  • Appendix E - 1732E ArmorBlock I/O Embedded Web Server
    • Introduction
    • Typical Applications
    • Browser Requirements
    • Access the Home Page of the Web Server
    • Log Into the Web Server
    • Navigate the 1732E ArmorBlock I/O
    • Access Diagnostic Information
  • Glossary
  • Index
  • How Are We Doing?
• Back Cover