Document Outline

• Chapter 1 General Information
• Chapter 2 Installation
  • Mechanical Installation
    • Panel Mounting
    • DIN Rail Mounting
  • Remote Display Installation
    • Mechanical Installation
      • Standard Cutouts
      • (ANSI 4" round or DIN 92x92 mm square)
      • Special Cutout
    • Electrical Connection
  • Electrical Installation
    • Typical Installation
    • Terminals
    • Power Source Connection
    • Chassis Ground Connection
    • Wiring Diagrams
  • I/O Connections
    • Relay Outputs
    • Digital Inputs
    • Analog Outputs
    • Analog Inputs
  • Communications Connections
    • COM1 RS-232 Connection
    • COM1 RS-422/485 Connection
    • COM1 Dial Up Modem Connection
    • COM1 Ethernet Connection
    • COM1 Profibus Connection
    • COM2 RS-422/485 Connection
• Chapter 3 Display Operations
  • Indicators and Controls
    • Display Diagnostics
    • Numeric LED Display
    • Load Bar Graph
    • Energy Pulse LED
    • Port Activity LEDs
    • Navigation Buttons
  • Data Display
    • Display Features
      • Measurement Units
      • Primary and Secondary Volts
      • Phase Power Readings
      • Fundamental Component
      • Auto Return
      • Auto Scroll
    • Navigation Buttons
    • Simple Reset of Accumulated Data
    • Common Measurements Display
    • Min/Max and Max. Demands Display
    • Power Quality/Harmonics Display
    • Energy Display
  • Status Display
  • Using the Menus
    • Navigation Buttons
    • Selecting Menus
    • Entering the Password
    • Selecting a Menu Entry
    • Viewing and Changing Setup Items
  • Menu Operations
    • Basic Device Settings
    • Device Options
    • Communication Ports
      • COM1 Settings
      • COM2 Settings
    • Network Address
    • Counters Setup
    • Control Setpoints Setup
    • Analog Inputs Setup
    • Analog Outputs Setup
    • Analog Expander Setup
    • Timers Setup
    • Display Setup
    • Meter Security
    • Setting the Device Clock
    • Resetting Accumulators and Maximum Demands
• Chapter 4 PAS Application Software
  • Configuration Database
  • Setting up Communications
    • Communicating through a Serial Port
      • Configuring a Serial Port
      • Selecting the Communications Protocol
    • Communicating through a Dial-up Modem
      • Configuring a Modem
      • Selecting the Communications Protocol
    • Communicating through the Internet
  • Setting Up the Meter
    • Downloading Setup to the Meter
    • Uploading Setup from the Meter
  • Authorization
  • Configuring Communications in your Meter
    • Setting Up Communication Ports
    • Setting Up the Ethernet
    • Configuring GE EGD Production Exchanges
  • General Meter Setup
    • Basic Meter Setup
    • Device Options
      • Power Calculation Modes
    • Local Settings
      • Daylight Savings Time
      • Time Synchronization Pulses
    • Using Digital Inputs
    • Using Relay Outputs
      • Generating Energy Pulses through Relay Outputs
    • Programming Analog Inputs
      • Scaling Non-directional Analog Inputs
      • Scaling ±1mA Analog Inputs
      • Scaling Analog Inputs for 0-2 mA and ±2 mA
    • Programming Analog Outputs
      • Scaling Non-directional Analog Outputs
      • Scaling Directional Power Factor
      • Scaling ±1mA Analog Outputs
      • Scaling Analog Outputs for 0-2 mA and ±2 mA
    • Programming the Analog Expander
    • Using Counters
    • Using Periodic Timers
    • Using Control Setpoints
      • Using Logical Expressions
      • Using Numeric Triggers
      • Using Binary Triggers
      • Using Event Flags
      • Using Interval Timers
      • Using Time Triggers
      • Delaying Setpoint Operations
      • Using Setpoint Events and Actions
      • Recording Setpoint Events
  • Configuring Summary Energy and TOU Registers
    • Setting up Total and Tariff Registers
    • Configuring the Daily Tariff Schedule
    • Configuring the Season Tariff Schedule
  • Configuring Recorders
    • Configuring Device Memory
    • Configuring the Event Recorder
    • Configuring the Data Recorder
      • Conventional Data Log Files
      • Factory Preset Periodic Data Logs
      • TOU Profile Data Log Files
    • Configuring the Waveform Recorder
    • Configuring the IEEE 1159 Power Quality Recorder
      • PQ Events Evaluation
      • PQ Recorder Setup
      • Power Quality Event Indication
  • Configuring Communication Protocols
    • Configuring Modbus
      • Modbus Point Mapping
    • Configuring DNP3
      • DNP Options
      • Configuring DNP Class 0
      • Configuring DNP Event Classes
  • Remote Device Control
    • Remote Relay Control
    • Event Flags
    • Device Diagnostics
    • Updating the Clock
    • Resetting Accumulators and Clearing Log Files
  • Administration
    • Changing a Password
  • Upgrading Device Firmware
  • Monitoring Devices
    • Viewing Real-time Data
    • Viewing Min/Max Log
    • Viewing Real-time Waveforms
    • Viewing Harmonic Spectrum and Synthesized Waveforms
  • Retrieving Log Files
  • Viewing Recorded Files
    • Viewing Options
    • Viewing the Device Event Log
      • Filtering and Sorting Events
      • Linking to Waveforms and Data Records
      • Selecting Primary and Secondary Units
    • Viewing the IEEE 1159 Power Quality Event Log
      • Filtering and Sorting Events
      • Selecting Voltage Units
      • Linking to Waveforms
      • Retrieving Waveforms Online
      • Viewing the ITI (CBEMA) Curve
    • Viewing the IEEE 1159 Statistics Report
      • Changing the Report Time Range and Contents
      • Customizing Reports
      • Printing Reports
    • Viewing the Data Log
      • Viewing Data Trend
    • Viewing Waveforms
      • Selecting Waveform Channels
      • Using the Marker Lines
      • Delta Measurements
      • Selecting the Time Axis
      • Viewing Phasor Diagrams
      • Viewing Symmetrical Components
      • Selecting Primary and Secondary Units
      • Using a Zoom
      • Customizing Line Colors and Styles
      • Viewing an RMS Plot
      • Viewing a Spectrum Chart
      • Viewing a Spectrum Table
      • Viewing a Frequency Plot
    • Viewing Synchronized Waveforms
  • COMTRADE and PQDIF Converters
    • Manual Converting
    • Automatic Converting
• Appendix A Technical Specifications
  • Environmental Conditions
  • Construction
  • Power Supply
  • Input Ratings
  • Relay Outputs
  • Digital Inputs
  • Optional Analog Inputs
  • Optional Analog Outputs
  • Communication Ports
  • Real-time Clock
  • Log Memory
  • Display Module
  • Standards Compliance
  • Measurement Specifications
• Appendix B Parameters for Analog Output
• Appendix C Setpoint Triggers and Actions
  • Setpoint Triggers
  • Setpoint Actions
• Appendix D Parameters for Monitoring and Data Logging
• Appendix E Data Scales
• Appendix F Device Diagnostic Codes