Document Outline

• Introduction
  • About QualiPHY
  • About QPHY-HDMI
  • Required Hardware
  • Test Fixtures
  • Required Host Computer System
  • Install Base Application
  • Activate Components
  • Set Up Dual Monitor Display
  • Set Up Remote Control
    • Configure Oscilloscope for Remote Control
    • Add Connection to QualiPHY
    • Select Connection
  • Accessing the Software
  • General Setup
    • Connection tab
    • Session Info tab
    • Report tab
    • Advanced tab
    • About tab
  • QualiPHY Test Process
    • Set Up Test Session
    • Run Tests
    • Run Reports
  • Customizing QualiPHY
    • Copy Configuration
    • Select Tests
    • Edit Variables
    • Edit Test Limits
  • X-Replay Mode
• QPHY-HDMI Testing
  • Test Preparation
    • Required Test Modes
    • Physical Setup
    • Deskew
  • QPHY-HDMI Test Configurations
    • Clock and Data0 Basic Tests
    • Clock and Data0 Tests at All Standard Frequencies
    • Data0 & Data1 & Data2 Inter-Pair Skew (7-6)
    • Clock and Data0 Tests at Custom Frequency (340 MHz)
    • Demo of All Tests
  • QPHY-HDMI Test Descriptions
    • Test7-2: TMDS-VL
      • Requirement
      • Methodology
    • Test7-4: TMDS TRise, TFall
      • Requirement
      • Methodology
    • Test7-5: TMDS Over/Undershoot
    • Test7-6: TMDS Inter-Pair Skew
      • Requirement
      • Methodology
    • Test7-7: TMDS Intra-Pair Skew
      • Requirement
      • Methodology
    • Test7-8: TMDS Clock Duty Cycle
      • Requirement
      • Methodology
    • Test7-9: TMDS Clock Jitter
      • Requirement
      • Test Methodology
    • Test7-10: TMDS Data Eye Diagram
      • Requirement
      • Methodology
  • QPHY-HDMI Variables
    • Execution Order Mode
    • Demo Mode
    • HDMI version tested
    • Number of sweeps acquired for a measure
    • User defined signal vertical gain
    • User defined signal vertical offset
    • Re-use vertical settings
    • Save acquired waveforms
    • Silent mode control
    • TMDS Data Pair to test
    • Use stored trace for pixel clock measure optimization
    • Waveform Path
    • Specific to “Test7-2: TMDS-VL” Group
      • Number of segments acquired in sequence
      • Recalled Waveform File Index (5 digits)
      • Support of TMDS frequency >= 165 MHz
    • Specific to “Test7-4: TMDS TRise, TFall” Group
      • Recalled Waveform File Index (5 digits)
      • Use internal peak if signal has two peaks
    • Specific to “Test7-6: TMDS Inter-Pair Skew” Group
      • Data-Data test combinations
      • Recalled Waveform File Index (5 digits)
    • Specific to “Test7-7: TMDS Intra-Pair Skew” Group
      • Number of segments acquired in sequence
        • Recalled Waveform File Index (5 digits)
    • Specific to “Test7-8: TMDS Clock Duty Cycle” Group
      • Number of segments acquired in sequence
      • Recalled Waveform File Index (5 digits)
    • Specific to “Test7-9: TMDS-Clock Jitter” Group
      • DUT TMDS Clock Standard Frequencies
      • DUT TMDS Clock Alternate Frequencies
      • Timebase used to create Eye Diagram
      • Recalled Waveform File Index (5 digits)
    • Specific to “Test7-10: TMDS-Data Eye Diagram” Group
      • DUT TMDS Clock Standard Frequencies
      • DUT TMDS Clock Alternate Frequencies
      • Recalled Waveform File Index (5 digits)
      • Timebase used to create Eye Diagram
  • QPHY-HDMI Limit Sets
• Manual Deskewing Procedures
  • Cable Deskewing Using the Fast Edge Output
  • Cable Deskewing Using the DUT Signal
• Error Messages