Hasbro Star Wars Darth Vader Voice Changer 85412 - Manual

VOICE BUTTON
VOICE
SWITCH
PHRASES BUTTON
BREATHING BUTTON
VOICE SWITCH
The voice switch has 3 different settings and a “demo” setting. This toy is
packaged in the “demo” setting for in-store demonstration purposes. You
will need to slide the switch to any of the other 3 settings for full activation of
the features. NOTE: Speech function is disabled in “demo” setting.
The mechanism helps you sound like Darth Vader.
To make your voice sound even more like Vader’s,
try this while using the toy:
• Choose a setting: The 3 settings alter your
voice in different ways. Try each setting to see
which one makes your voice sound closest to
the way Darth Vader sounds.
• Listen to the actual phrases to learn the pace
at which Darth Vader speaks.
• Deepen your voice as you talk.
• Talk slowly and clearly.
• Speak into the microphone and get your mouth as close to the
microphone as possible.
VOICE BUTTON
Wearing the helmet and chestplate, press the Voice Button and speak. Your
voice will change, to sound like Darth Vader’s! See the above instructions on
settings and voice adjustment to fine-tune the sound.
PHRASES BUTTON
Wearing the helmet and chestplate, press the Phrase Buttons to hear Darth
Vader’s actual phrases from the movies!
The phrases are: “You don’t know the power of the dark side.”
“There is no escape.”
“The Force is with you.”
“Your powers are weak.”
“Don’t make me destroy you.”
BREATHING BUTTON
Wearing the helmet and chestplate, press the Breathing Button to hear Darth
Vader’s actual breathing sounds from the movies!
*
Product and colors may vary.
© 2007 Lucasfilm Ltd. & ® or TM where indicated. All rights reserved.
®* and/or ™* & © 2007 Hasbro. All Rights Reserved.
® denotes Reg. U.S. Pat. & TM Office.
*
"DEMo"
SETTING #3
SETTING #1
SETTING #2
FCC Statement:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy, and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
TO REPLACE BATTERIES
Loosen screw in battery compartment door with a Phillips/cross head
screwdriver (not included). Remove door. Remove and discard batteries. Insert
3 x 1.5V “AA” or R6 size batteries. Alkaline batteries recommended. Replace
door, and tighten screw.
WEARING HELMET
Place mask on face. Place headgear straight down on head, aligning rib
inside headgear with indentation on back of mask. Slide headgear forward
until you hear a click (tab on front of headgear will lock into slot between
the eyes in the mask). To remove headgear, lift tab on front of headgear.
1.
HEADGEAR
P/N
6748650000
MASK
RIB
TAB
PRESS IN To lATcH
Pull ouT To uNlocK
2.
VoIcE SWITcH (Front View)
cHESTPlATE
(See inset above) IMPORTANT! PLEASE READ INSTRUCTIONS COMPLETELY BEFORE WEARING TOY.
ADJUSTABLE STRAPS
The mask has adjustable straps on the front, sides and back. To adjust,
lift straps off posts, slide straps to desired position, and press straps
onto posts.
SIDE SIDE
FRoNT
BAcK
AGES 5
through adult
85412
! CAUTION:
1. Always follow the instructions carefully. Use only batteries
specified and be sure to insert them correctly by matching the +
and – polarity markings.
2. Do not mix old batteries and new batteries, or standard (carbon-
zinc) with alkaline batteries.
3. Remove exhausted or dead batteries from the product.
4. Remove batteries if product is not to be played with for a long
time.
5. Do not short-circuit the supply terminals.
6. Should this product cause, or be affected by, local electrical
interference, move it away from other electrical equipment.
Reset (switching off and back on again or removing and re-
inserting batteries) if necessary.
7. RECHARGEABLE BATTERIES: Do not mix these with any
other types of battery. Always remove from the product before
recharging. Recharge batteries under adult supervision. DO NOT
RECHARGE OTHER TYPES OF BATTERIES.
IMPORTANT:
BATTERY INFORMATION
Please retain this information for future reference.
Batteries should be replaced by an adult.
! CAUTION:
TO AVOID BATTERY LEAKAGE
1. Be sure to insert the batteries correctly and
always follow the toy and battery manufacturers’
instructions;
2. Do not mix old and new batteries or alkaline,
standard (carbon-zinc) or rechargeable (nickel-
cadmium) batteries;
3. Always remove weak or dead batteries from the
product.
x3
BATTERIES INCLUDED
1.5VAA/R6 size
Replace with 3 x 1.5V “AA” or R6 size batteries.
Alkaline batteries recommended. Phillips/cross
head screwdriver (not included) needed to
replace batteries.
x3
P I L A S I N C L U I D A S
AA/R6 (1,5 V)
A reemplazar por 3 pilas AA o R6 de 1,5 V con
un destornillador en cruz (no incluido). Se
recomiendan pilas alcalinas.