Horizon Fitness FITNESS T701 - Manual (Page 5)


in
Tr
Odu
CT
iO
n
im
PO
rT
an
T
Pre
Ca
uT
iO
ns
as
sem
Bl
Y
Be
FO
re
YO
u B
eG
in
Treadmill OP
er
aT
iO
n
limi
Ted
w
arr
an
TY
Tr
Ou
Ble
sHOO
Tin
G
&
main
Tenan
Ce
CO
ndi
TiO
nin
G
Guideline
s

in
Tr
Odu
CT
iO
n
im
PO
rT
an
T
Pre
Ca
uT
iO
ns
as
sem
Bl
Y
Be
FO
re
YO
u
Be
Gin
Treadmill OP
er
aT
iO
n
CO
ndi
Ti
Onin
G
Guideline
s
Tr
Ou
Ble
sHOO
Tin
G
&
main
Tenan
Ce
limi
Ted
w
arr
an
TY
Pre-assemBlY
ASSEMBLY sTeP 1
BOLT (A)
20 mm
Qty: 4 SPRING WASHER (B)
15 mm
Qty: 4 FLAT WASHER (C)
15 mm
Qty: 4
Hardware BaG 1 COnTenTs :
dO nOT aTTemPT TO liFT THe Treadmill! Do not move or lift
treadmill from packaging until specified to do so in the assembly instructions.
Failure to do so may result in injury! Remove plastic wrap from console masts.
nOTe: During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in
before completely tightening any ONE bolt. NOTE: A light application of grease may aid in the installation
of hardware. Any grease, such as lithium bike grease is recommended.
WARNING
Cut the yellow banding straps and lift the runninG deCK upward until the FOOT laTCH locks.
Remove all contents from underneath the runninG deCK.
Open Hardware BaG 1.
With the runninG deCK in the raised position, attach the leFT COnsOle masT to the Base Frame
using 4 BOlTs (a), 4 sPrinG wasHers (B) and 4 FlaT wasHers (C).
a
B
C
ASSEMBLY sTeP 2
Open Hardware BaG 2.
Pull lead wire through riGHT COnsOle masT. After pulling the lead wire through the mast, the
top of the COnsOle CaBle should be located at the top of the mast. Detach and discard lead wire.
With the runninG deCK in the raised position, attach the riGHT COnsOle masT to the Base Frame
using 4 BOlTs (a), 4 sPrinG wasHers (B) and 4 FlaT wasHers (C).
nOTe: Be careful not to pinch any cables while attaching the riGHT COnsOle masT.
a
B
C
BOLTS (A)
SPRING WASHERS (B)
FLAT WASHERS (C)
LEFT CONSOLE MAST
BASE FRAME
RUNNING DECK
FOOT LATCH
BOLT (A)
20 mm
Qty: 4 SPRING WASHER (B)
15 mm
Qty: 4 FLAT WASHER (C)
15 mm
Qty: 4
Hardware BaG 2 COnTenTs :
BOLTS (A)
SPRING WASHERS (B)
FLAT WASHERS (C)
RIGHT CONSOLE MAST
CONSOLE CABLE
LEAD WIRE
BASE FRAME
RUNNING DECK
T701_Rev.1.2.indd 8-9 9/17/08 4:55:47 PM