FELLOWES DS-2 - Manual (Page 2)

Sensor lights up
Touch test area
Press Auto-On ( )
SafeSense™ T
echnology (yellow)
Overheated (red)
See safety instructions below
GLISH
EENENENENGENGENGENGENGLENGLENGLIENGLISENGLISENGLISENGLISHENGLISHENGLISHENGLISHENGLISHENGLISHENGLISHENGLISHENGLISHENGLISHENGLISHENGLISHENGLISHENGLISHENGLISHENGLISHENGLISH
Model DS-2Model
DS
2
— T
o T
est SafeSense
™
Technology
IMPOR
TANT
SAFETY
INSTRUCTIONS — Read Before Using!
Auto-On ( ) Off Reverse (R)
CAP
ABILITIES
Breakthrough Safety T
echnology! SafeSense™ stops shredding when hands are too close to the opening.
Standby (green)
Control switch
Sh
re
dd
er
hea
d
Paper entr
y
Waste opening (Bin full indicator)
SafeSense™ override switch
Active
Not Active
Window
•
Keep away from children and pets. Keep hands away from paper entr
y. Always unplug when not in use.
•
Keep foreign objects – gloves, jewelr
y, clothing, hair
, etc.– away
from shredder openings. If object enters top opening, press and hold Reverse (R) to back out object.
•
Never use aerosol, petroleum-based or other flammable products on or near shredder
. Do not use canned air on shredder
.
•
Do not use if damaged or defective. Do not open shredder head. Do not place near or over heat or water source.
•
8 sheets per pass to avoid jams.
•
Avoid touching exposed blades under Confetti-Cut shredder head.
•
The socket-outlet shall be installed near the equipment and shall be easily accessible.
Will shred:
Paper
, small paper clips, credit cards and staples
Will not shred:
Continuous forms, adhesive labels, transparencies, newspaper
,
cardboard, large paper clips, laminates or plastic other than noted above Paper shred size: Confetti-Cut
.....................................................................
5/32” x 2” (3.9 x 50mm)
Maximum: Sheets per pass (Confetti-Cut)
...............................................................................
8*
Cards per pass
.......................................................................................................
1
Passes per day
...............................................................................................
10-20
Paper width
............................................................................................
9”/229mm
Continuous operation
.............................................................................
2-4 minutes
*20 lb., 8.5”x11” paper at 120v
, 60 Hz,
3.5
Amps; heavier paper
, humidity or other
than rated voltage may reduce capacity
.
Set to Off
Feed into paper entr
y
and release
Set to Off
LIMITED W
ARRANTY Fellowes, Inc. (“Fellowes”) warrants the cutting blades of the machine to be free from
defects in material and workmanship for 5 years from the date of purchase by the original consumer
.
Fellowes warrants all other parts of the machine to be free of defects in material and workmanship for 1 year from the date of purchase by the original consumer
. If any part is found to be defective during the
warranty period, your sole and exclusive remedy will be repair or replacement, at Fellowes’ option and expense, of the defective part. This warranty does not apply in cases of abuse, mishandling, or unauthorized repair
. ANY IMPLIED
W
ARRANTY
, INCLUDING THA
T OF MERCHANT
ABILITY OR FITNESS FOR A P
AR
TICULAR PURPOSE, IS HEREBY
LIMITED IN DURA
TION TO THE APPROPRIA
TE W
ARRANTY PERIOD SET FOR
TH ABOVE. In no event shall
Fellowes be liable for any consequential or incidental damages attributable to this product. This warranty gives you specific legal rights. The duration, terms, and conditions of this warranty are valid worldwide, except where different limitations, restrictions, or conditions may be required by local law
.
For more details or to obtain ser
vice under this warranty
, please contact us or your dealer
.
Gently pull uncut paper from paper entr
y. Plug in.
Set to Reverse (R) for 2-3 seconds
Set to Off (O) and unplug
Set to Reverse (R)
Run regularly in reverse for one minute Oil when bin is full, or immediately
, if:
• Capacity
decreases
•
Motor sounds different, or Shredder stops running OPERA
TION
TROUBLESHOOTING MAINTENANCE
3
Shredder doesn’t start:
Follow oiling procedure below and repeat twice.
W
ARRANTY
Alternate slowly back and forth
*Apply oil across entr
y
Press and hold Reverse (R) 2-3 seconds
Shred one sheet
Set to Off
Press Auto-On ( )
Ye
llow - SafeSense™ active
Ye
llow flashing - SafeSense™ not active
Make sure head is on basket correctly Wa
it 15 minutes for motor to cool down
Remove and empty basket
Press Auto-On ( )
Paper jam:
Set to Off (O), remove shredder head and empty bin. Replace shredder head, and follow any or all of the
below procedures.
PAPER CARD
*Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250
ATTENTION:
If the SafeSense™ light remains on, you must engage the
Override Switch
in order to perform steps above. Once the jam is cleared, reset the
SafeSense™ feature. (See SafeSense™ instructions below
.)
SafeSense™ override switch
Active
Not active
Sensor light illuminated–paper
jammed
SafeSense™ paper jam:
If the SafeSense™ feature activates (SafeSense™ light remains on) to cause the user
to think the shredder has jammed when it has not, use the
Override Switch
to deactivate the SafeSense™
feature and clear the paper
. W
arning
– when switch is in override position, the SafeSense™ light will flash and
the SafeSense™ feature will NOT function. Once the paper is cleared, reset the SafeSense™ feature.
Plastic
bas
ke
t
Gri
ps
Handle
SET
-UP
Place head on basket as shown:
Feed into paper entr
y
and release
Press Auto-On ( )
Continuous operation: 2-4-minute maximum NOTE:
Shredder
runs
briefly
after each pass to clear entr
y.
Continuous operation beyond 2-4-minutes will trigger 15-minute cool down period.