FieldServer FS-8704-09 SNMP - Manual (Page 35)

FS-8704-09 SNMP Driver Manual Page 35 of 39
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com
Tel: (408) 262 2299 Fax: (408) 262 9042 Toll Free: (888) 509 1970 email: [email protected]
Message Description/Action
SNMP:#18 Err. Bad Send IP=%s
The IP address for a remote SNMP server (agent) has probably
been incorrectly specified. Check the configuration file.
5
SNMP:#19 Err. Can’t send to
Agent/Trap Dest. %s at %s
The FieldServer cannot reach the specified remote Node. The
message prints the Node name and the IP address. This message is
most commonly printed when:
•
The wrong IP address has been specified.
• The remote Node is off or in an error state
6
SNMP:#20 Err. Received
set/get/getnext request
The Client side of the driver has received a request. It should only
receive responses.
6
SNMP:#21 Err. Bad community
string The SNMP message contains a badly formatted community string or
the community string is absent. Read notes for msg#23
SNMP:#22 Err: Cant parse msg:
found %#x at %d
A response to a poll from the FieldServer contains a bound variable
that is not supported or expected. For example an IP_ADDRESS
and OPAQUE variable or a TRAP. Immediately after this message
the driver prints a hex dump of the offending message. Ensure that
the remote SNMP server is correctly configured. Review the Driver
fact Sheet for supported features. If you are confident that the FS
should process the message correctly then capture a log and call
tech Support.
5
SNMP:#23 Err. Invalid Msg
The Server side of the driver has received a message from a SNMP
client which is not correctly formatted or which contains bound
variables/features not supported by the driver. This particular error
message is printed when the SNMP message does not begin with
0x30.
5
SNMP:#24 Err. Message length
error The SNMP message indicates that a message length is different to
the number of bytes received.
5
SNMP:#25 Err. Could not get
Request ID
The SNMP message number is badly formatted or absent.
5
SNMP:#26 Could not get Error
Status
The SNMP error status field is badly formatted or absent.
5
SNMP:#27 Could not get Error
Index
The SNMP error id field is badly formatted or absent
5
SNMP:#28 Expected
SNMP_TYPE_SEQ
The message header is correctly formatted but as the driver
continues parsing the message it can’t find the bound variables.
6
SNMP:#29 ERR. Couldn’t
respond to Get Request for OID
Immediately after this message the driver prints the value of the
offending OID. The driver can only serve data for configured OID
points.
The OID must correspond to a FST system OID. 1.3.6.1.4.1.6347
and there must be a data array to serve the point (read Appendix A
for more information). To resolve this problem you will have to
reconfigure the remote client or the FS.
5
SNMP:#30 FYI Int
IP=%d.%d.%d.%d.%d Ext=%s
The Server side of the FieldServer can discover the IP address of
the source Node from the IP packet header. The source Node IP
address can also be reported inside the SNMP portion of the
Ethernet message. This message is pronted if the tow IP addresses
are different and is for information only. The driver uses the IP
address contained in the SNMP portion of the message to locate a
matching Node in the configuration. You may need to edit the
configuration and change the IP address of the Node which sends
6
Edit the configuration file, downloaded the modified file to the FieldServer and restart the FieldServer for
the changes to take effect.