Fantom Vacuum AP500H - Manual (Page 8)

OPERATING INSTRUCTIONS
1. On/Off Button
2. Fan Speed Button
3. Timer
4. Set-Up
5. Neutralize Button
6. Ionizer Button
7. Increase Button
8. Decrease Button
The Remote Control
7
IMPORTANT: The remote control requires
two (2) AAA batteries which are not
included with the unit. Do not mix old and
new batteries. Do not mix alkaline,
standard (carbon-zinc) or rechargeable
(nickel-cadmium) batteries together.
NOTE: The remote control functions best
at a distance of less than 20 feet (6
meters).
1. On/Off Power Button
This controls the power to the unit.
2. Fan Speed Button
Each time this button is pressed it
will cycle through the options for the
fan speed. (See Using the Air Purifier.)
3. Timer Button
This button only controls when the
unit will shut-off automatically.
4. Set Up Button (Pre-Program)
This allows you to pre-program “On”
time, “Off” time, and fan speed.
This feature can be used even if the air
purifier is “Off”.
5. Neutralize
This button will turn on or turn off the
photo-catalysis and UV light functions
remotely.
6. Ionizer Button
This button will turn on or turn off the
ionizer function remotely.
7. Increase Button (“+”)
This button will increase time selected
in the set up feature by half hour
increments.
8. Decrease Button (“-”)
This button will decrease time selected
in the set up feature by half hour
increments.
Fig. 7
2. While the unit is “Off”, press the
set up button on the remote
control. The “On” will flash on the
timer display panel.
3. Press the “+” or the “-” button on
the remote control to set the time.
Each time you press the “+”
button, the time will increase or
decrease up to a maximum of
9 hours and 30 minutes.
The “+” button will increase the
time by 30 minute increments and
the “-” button will decrease by 30
minute increments.
4. To set the time when the unit will
turn “Off”, depress the set up
button again. The “Off” will flash
on the display panel. Repeat step
#3 to select desired “Off” time.
5. Depress the set up button on the
remote control again to set the fan
speed that is desired. The circle
diagram around the fan speed will
flash indicating that fan speed will
now be adjusted.
6. Depress the fan speed button or
the increase (“+“) to the required
fan speed.
7. Once the fan speed is selected,
after a moment a single “beep” will
indicate a successful set-up and
the display panel will display how
many hours and minutes remain
until the unit turns “On”.
IMPORTANT : Three (3) “beeps”
and a blank panel indicates incorrect
data entry. Repeat set-up process.
NOTE: Auto fan speed is the only
setting the dust sensors use to adjust
the fan speed to what is required to
clean the air. Manual adjustment is
required if the unit is not in auto
mode.
To Pre-Program Your Air
Purifier
Use the set up control button on the
remote to preset when the unit will
turn “On”, “Off”, and which fan speed
is desired when the unit is running.
1. Each time the set up button is
pressed it goes through one of
three cycles. (Fig. 7)
OPERATING INSTRUCTIONS
6
Ionizer
NOTE: The neutralize and the ionizer
functions are silent features, the only way
to know if they are “On” is with the
indicator lights.
1. To turn the ionizer “On”, press the
ionizer button on the control panel or
the remote control. The ionizer “On/Off”
indicator will illuminate when “On.
2. To turn this feature “Off”, depress the
ionizer control button or remote button
again. The ionizer “On/Off” indicator
will no longer be illuminated. (Fig. 4)
Neutralize
The neutralize button turns the UV light
“On” and begins the photo-catalysis
process.
1. To turn the neutralize feature “On”,
press the neutralize button on the
control panel or the remote control.
The neutralize indicator light will
illuminate when the feature is “On”.
(Fig. 5)
2. To turn this feature “Off” depress
the neutralize button again on
control panel or remote. The
neutralize indicator light will no
longer be illuminated.
Using the Timer
The timer button has 5 different cycles
for automatic shut off. To use the timer
button:
1. Depress the timer control button to
preset when the unit will turn “Off”.
2. With this feature, you have a choice
of 1hr, 2 hrs, 4 hrs or 8 hrs. (Fig. 6)
The Odor Sensor
If the air purifier senses odors in the air,
the indicator bar will increase to a
maximum of four (4) bars. Adjust the fan
speed to a desired level. The air purifier
will automatically adjust the fan speed
when it is in “AUTO” mode. (Fig. 3)
Fig. 6
The Dust Sensor
When more dust is detected in the air
the indicator bar will increase to a
maximum of four (4) bars. Adjust the
fan speed to desired level. The air
purifier will automatically adjust the fan
speed when it is in “AUTO” mode.
(Fig. 3)
Fig. 3
Ionizer
Button
Ionizer
Indicator Light
Fig. 4
Neutralize Button
Fig. 5 Neutralize
Indicator Light
Odor Sensor
Indicator Bar
Dust Sensor
Indicator Bar