Troubleshooting, Instruction manual 25 – Festool Domino DF 500 User Manual

Page 25

Advertising
background image

Instruction Manual

25

Troubleshooting

Symptom Possible

Causes

Motor does not start

►

Check that the cord is properly plugged into an outlet.

►

Make sure the Plug-it connector is properly inserted and fully tightened.

►

Make sure the outlet has power. Check the circuit breaker or try another outlet.

►

If used with a Festool dust extractor, make sure the selector switch is pointing to
"Auto". The auxiliary outlet on the dust extractor has power only when the selector
is at Auto.

►

Inspect the power cord (including extension cords) for damage or missing prongs.

►

The motor brushes may have worn and need replacement.

Plunging action is not smooth

►

Clean the linear rails and bronze bearings of the plunge slide, and make sure they
are properly lubricated (refer to the

Routine Maintenance

instructions on page 20).

►

Inspect the linear bearings for damage. Improper insertion of the fence body onto
the motor housing can damage the linear bearings.

Domino tenons are too loose

►

Make sure you hold the Domino joiner firmly in position while plunging the mortise
slot.

►

Make sure the mortise width setting is correct.

►

Make sure you are using the correct mortising bit for the size of the Domino tenon.

►

The Domino tenons may have shrunk in an overly dry or warm environment. This is
normal wood movement.

►

Check the mortising bit to ensure it is not bent. A bent bit will make a thicker and
wider mortise slot than desired.

►

Plunging too fast can cause the mortise slot to be enlarged.

Domino tenons are too tight

►

The most common cause for this is that the tenons are stored in a humid
environment, and they have swelled from moisture absorption. Store the tenons in
a cool dry environment.

►

The mortising bit may have been improperly sharpened or sharpened too many
times. Replace the bit.

Workpiece joints are
misaligned horizontally

►

Make sure the workpiece is securely clamped before plunging.

►

Check the calibration of the locating pins.

►

Check the calibration of the horizontal position gauge (sight gauge).

►

Don’t plunge the mortising bit into the work too fast. This may cause the joiner to
move during the plunge.

►

Make sure the friction pads on the front of the joiner are not worn, damaged, or
missing.

Workpiece joints are
misaligned vertically

►

Take care not to tilt the joiner while plunging.

►

If the mortise slots were registered from the bottom of the baseplate, make sure
there is no dust or debris under the joiner.

►

Make sure the fence is properly locked at the desired height setting.

►

Inspect the fence height adjustment lock to ensure it is not broken (slipping).

Tilted or misaligned mortise
slots

►

Make sure the fence is set to the correct angle (e.g. 90 degrees).

►

Make sure to hold the Domino joiner firmly to the work surface.

►

When tightening the height adjustment clamp lever, make sure the fence is not
being skewed. Try wiggling the fence slightly as you tighten the clamping lever.

►

Plunging too slow can cause the mortise slots to be tilted slightly.

Workpiece joint won’t close
(gaps between pieces)

►

Make sure the proper plunge depth is set.

►

Make sure the mortising bit is not broken.

►

Make sure the joiner is tight to the face of the workpiece.

►

The mortising bit may have been sharpened too many times and is too short.

►

Excessive dust may be present inside the linear slide.

►

Excessive glue may be present at the bottom of the mortise.

Tearout or rough mortise slots

►

Plunging speed too fast. Slow down the rate of your plunge.

►

Low-grade materials and plywoods will tear out more than solid woods. Decreasing
your plunging speed will improve the results but may not eliminate the problem
completely.

►

Dull or broken mortising bit.

Tapered mortise slot. The
Domino tenon fits only part
way into the slot

►

The plunge speed is too fast and the bit is not cutting the sides properly. Slow
down the plunge speed.

Advertising