FELLOWES c120ci - Manual (Page 2)

K. Control Panel and LEDs
1. Reverse
2. ON/OFF
3. Forward
4. Bin full
5. Door open
Jam Proof System
Eliminates frustrating jams
by preventing overloads and
powering through misfed paper
2
KEY
Patented SafeSense ® Technology
Stops shredder immediately
when hands are too close to
the paper entry
CAPABILITIES
AdvANCEd PRoduCT fEATuRES
ENGLISH
Model C-120i/C-120Ci
Will shred: Paper, credit cards, CD/DVD’s, staples and small paper clips
Will not shred: Adhesive labels, continuous form paper, transparencies, newspaper,
cardboard, large paper clips, laminates, file folders, X-rays or plastic other than noted above
Paper shred size:
Cross-Cut .....................................................5/32 inches x 1-1/2 inches (3.9mm x 38mm)
Strip Cut ........................................................................................... 7/32 inches (5.8mm)
Maximum:
Sheets per pass ........................................................................................................... 18*
CDs/Cards per pass ....................................................................................................... 1*
Paper entry width .................................................................................. 9 inches (230mm)
*8.5 inches x11 inches, 20lb., (75g) paper at 120V, 60 Hz, C-120i 6 Amps, C-120Ci
8 Amps; heavier paper, humidity or other than rated voltage may reduce capacity.
Recommended daily usage rates: 100-150 paper passes; 100 cards; 10 CDs
Fellowes SafeSense ® shredders are designed to be operated in office environments ranging
between 50 – 80 degrees Fahrenheit (10 – 26 degrees Celsius) and 40 – 80% relative humidity.
A.
B.
D.
C.
K.
I.
G.
Sleep Mode
Energy saving feature shuts down
automatically after 2 minutes of
no shredding activity
A. SafeSense
®
Technology
B. Paper entry
C. CD entry
D. Door
E. Basket (paper)
F. Basket (CD)
G. See safety instructions
H. Casters (2)
I. Disconnect power switch
J. Shipping bolts (wing nuts)
To be removed prior to operation
6. Remove paper
7. Overheat
8. Sheet capacity indicator
9. SafeSense
®
indicator (yellow)
10. Auto button
H.
INSTALLATIoN INSTRuCTIoNS
1. Place shredder against the wall (drywall, wooden, or concrete).
Mark screw locations on wall through back of cabinet.
2. Drill 1/4" hole in wall for the anchor plugs.
3. Insert white plastic anchor plugs into drilled holes.
4. Insert (2) screws through back of cabinet and thread black rubber spacer onto the screw.
5. From inside cabinet use Phillips screw driver to secure shredder to the wall.
IMPoRTANT SAfETY INSTRuCTIoNS — Read Before using!
15
15
15
15
• Keep away from children and pets. Keep hands away from paper
entry. Always set to off or unplug when not in use.
• Keep foreign objects – gloves, jewelry, clothing, hair, etc. – away
from shredder openings. If object enters top opening, switch to
Reverse ( ) to back out object.
• Never use aerosol products, petroleum based lubricants or other flammable
products on or near shredder. Do not use canned air on shredder.
• Do not use if damaged or defective. Do not disassemble shredder. Do
not place near or over heat source or water.
• This shredder has a Disconnect Power Switch (I) that must be in the ON
(I) position to operate shredder. In case of emergency, move switch to
OFF (O) position. This action will stop shredder immediately.
• Avoid touching exposed cutting blades under shredder head.
• Keep finger away from CD hole when shredding.
• Do not put foreign objects in paper entry.
• The grounded socket-outlet shall be installed near the equipment and shall be
easily accessible.
• WARNING: Shredder Stability - Secure Shredder to wall with hardware
provided following the instructions under Installation Instructions.
• Product is intended for commercial use only, and not for use around children.
Eliminates frustrating jams by preventing overloads and powering through misfed paper.
JAM PRoof SYSTEM oPERATIoN*
*100% Jam Proof when used in accordance with user manual
PREvENTIvE MAINTENANCE ANd MISCELLANEouS TRouBLESHooTING
• For peak performance, we recommend oiling shredder each time waste bin is emptied. Only use a non-aerosol vegetable oil.
Machines not oiled may lose sheet capacity, become noisy, and ultimately, stop running.
• Though paper detection sensors are designed to be maintenance free, the sensors occasionally become blocked by paper dust, causing the motor to run even
if there is no paper present. Both sensors are located in the center of the paper entry.
• Self Cleaning Cycle: Shredder periodically cycles in forward and reverse lasting 3-6 seconds.
• Empty wastebasket when bin full indicator lights up.
• Shredder won’t run if the door is open, or bin needs to be emptied.
• Maintenance is an important part of protecting your investment. Don’t forget our oil (35250) and shredder bags (36054).
• When shredding for a prolonged period of time, the motor can become warm and require a cool down period. When this occurs the overheat indicator will alert you to the
problem, this model will require 45 minutes to cool down.
Go to Support Section at www.fellowes.com or see back page of manual for useful telephone numbers.
3
SAfESENSE ® TECHNoLoGY oPERATIoN SLEEP ModE
AUTO
WHEN IN SLEEP ModE
1 2 3
In sleep mode To get out of sleep mode
touch control panel
insert paper or
Advanced Jam Prevention- Electronically
measures paper thickness to prevent paper jams:
Continue 100% Jam
Proof Shredding
1 2 3
Up to RED: Too Many
sheets have been inserted.
Up to GREEN: More sheets
can be added.
Up to YELLOW: Productivity
is optimized.
If a misfeed
occurs:
If illuminates after paper has been
reversed, press reverse and remove paper.
Otherwise, regular shredding will resume.
All indicators light up and
shredder pauses for 3-6 seconds Wait for flashing to stop after automatic correction
is complete. Regular shredding will resume.
SET-uP ANd TESTING
AUTO
1
Turn the shredder ON
( ) to activate SafeSense
®
2
Touch test area and
look for the SafeSense
®
indicator to illuminate
SafeSense
®
is active and
working properly
3
Remove several sheets until
indicator is below red.
Do nothing and
shredder will go
automatically to
sleep mode
BASIC SHREddING oPERATIoN
Press ( ) ON to
activate
PAPER/CARd oR Cd
1
Feed paper/card
straight into paper
entry and release
3
Plug in and put
disconnect power
switch in ON (I)
position
To shred CDs rotate
CD flap into place
When finished
shredding set
to OFF ( )
or
7
www.fellowes.com features an extensive on-line support section with a number of self-service options
Continuous operation:
45 minutes maximum
NoTE: Continuous operation
beyond 45 minutes will trigger
45
minute cool down period.
4
AUTO
6
AUTO
2
Hold CD at edge,
feed into CD
entry and release
5 7