Fantom Vacuum VPW49H User Manual

Page 4

Advertising
background image

Fig. 18

Cleaning the Nozzles: If you notice that the

output pressure fluctuates, you may have to

clean the nozzles. Turn the unit "Off". Unplug

from electric outlet and disconnect the water

supply. Remove the lances, trigger gun and

hose from unit. Take the small metal pin

provided and insert into the nozzle end to

remove any obstructions. (Fig. 19)

Fig. 19

Hose Connector

Water Intake

This will occur more frequently if your

water supply is very hard.

Motor Thermostat
Important
:

This pressure washer is

equipped with a motor thermostat. The

motor will stop if it is overheating. Wait

10-20 minutes before starting the unit

again. If it stops again, please call

FANTOM customer service at

1 (800) 275-9251.

Ground Fault Circuit Interrupter
(GFCI)

This unit is equipped with a

Ground

Fault Circuit Interrupter (GFCI) built into

the plug. This device provides additional

protection from the risk of electrical

shock. When connecting the GFCI to the

electrical outlet, the indicator should

appear red. If the indicator is not red,

depress the RESET button on the GFCI

until the indicator appears red.

Cleaning Tips

Wood Decks: Rinse deck and

surrounding area with fresh water. If

using detergent, fill the detergent

applicator bottle and apply to the area

being cleaned. For optimal results,

reduce your work area to small sections

and clean each section one at a time.

Allow the detergent to rest on the surface

for a few minutes and then rinse at high

pressure. Do not let the detergent dry on

the deck. Always clean from left to right

and top to bottom for best results. Rinse

at high pressure using the fan jet keeping

the tip of the spray nozzle 8-12 inches

from the surface.

Caution: For soft

woods, increase the distance from the

cleaning surface.

Cars, Boats, & Motorcycles: Wet down

area to be cleaned before applying

detergent with clean water. Fill the

detergent applicator bottle and apply to

the area being cleaned. To achieve best

results, clean one side at a time. Allow

the detergent to rest on the surface for a

few minutes but do not let it dry. Rinse at

high pressure using the fan jet in a

sweeping motion keeping the tip of the

spray nozzle at least 8-10 inches away

from the surface. Maintain a further

distance when using a direct spray. Wipe

surface for a polished finish.

8

GETTING TO KNOW YOUR PRESSURE WASHER

OPERATING INSTRUCTIONS

Maintenance & Cleaning

Winterizing & Long Term Storage

1. Disconnect all water connections.

2. Turn the pressure washer on for a

few seconds, until any remaining

water in the pump exits.

3. Turn the unit off immediately.

4. Store the pressure washer, parts and

accessories in an area with a

temperature above 32°F.

Lubrication: The pressure washer is

supplied with a closed lubrication system,

so no addition of oil is needed.
Checking the Water Intake Filter: The

water intake filter is located inside the water

intake connector. (Fig. 18). Remove

periodically and inspect for any deposits

that might accumulate there.

15. Trigger

16. Trigger Lock

17. High Pressure Hose Connector

18. Brush

19. High Pressure Hose

20. Rotary Brush

21. Hose Connector

22. Garden Hose Coupling

23. Phillips Screw 1 1/4–inch long (x1)

(not shown)

24. Phillips Screw 7/8-inch long (x2)

(not shown)

25. Phillips Screw 1-inch long (x1 nickel plate)

(not shown)

Storing Your Pressure Washer

1. Pressure Washer

2.

Water Intake

3.

Water Intake Filter

4.

On/Off Switch

5.

Handle

6.

Detergent Tank

7.

High Pressure Output

8.

Power Cord

9.

Wheels (x2)

10. Wheel Locks (x2)

11. Front Support

12. Pressure Regulated Lance

13. Turbo Lance

14. Trigger Gun

When you have finished using your

pressure washer, follow these steps for safe

storage:

1. Turn the pressure washer to the "Off"

position.

2. Turn off the water supply.

3. Before disconnecting the high pressure

hose connection, point the trigger gun in

a safe direction away from you and

discharge the high pressure water.

Disconnect the high pressure hose from

the pressure washer and trigger gun.

4. Disconnect garden hose from pressure

washer.

5. Remove excess water from the pump by

tipping the unit on both sides to drain

any remaining water from the water

intake and outlet fittings.

6. Drain detergent tank and flush with clean

water.

7. Wipe away any remaining water on all

parts and fittings.

8. Engage the trigger gun safety lock.

9. Store the unit and accessories in a room

above 32°F.

Illustrations may differ from actual product.

Technical Specifications

Voltage:

120V., 60Hz.

Power:

13 Amps

Pressure:

1900 psi. (max)

Flow Rate:

1.65 GpH

3

Advertising