Initial setup, Camera and power connections, System operation – First Alert H.264 Digital DVD Pro-Dc8810-520/Pro-DC8410-520 User Manual

Page 4: Page 6 page 7, Step 1 ... installing cameras, Mounting cameras and running cable, Step 2 ... connecting devices, Step 3 ... system start up power on/off, Main menu access

Advertising
background image

Page 6

Page 7

initial setup

camera and power connections

initial setup

system operation

step 1 ... Installing cameras

Power to Camera

Mounting Cameras and Running Cable

Select the position for the camera and secure the camera stand. Screw the camera onto the stand. Adjust camera to the proper
view angle. Make sure the lens is upright relative to the subject. Tighten the thumb bolt. First Alert cameras can be either ceiling or
wall mounted by simply reversing the camera stand mounting. See “Camera Orientation” Info box. Holes are provided on both the
bottom and back of the camera housing to accommodate most mounting requirements. Run cable from camera to DVR location.
See Information box below on “Longer Cable Runs”.

Camera Orientation

It’s important the camera is mounted correctly to
ensure the image is not upside down as the cam-
era lens can only be positioned one way.

Longer Cable Runs

Longer cable runs may require an upgrade to
RG59 Coax cable. First Alert kits ship with eco-
nomical AV cable that is designed to work well up
to the length of cable provided, usually around
60 feet. If longer distances between camera and

DVR are required, you will need to upgrade to RG59 Coax cable. We
provide several lengths up to 300 feet. In addition, if you need to run
cable for in-wall installations, then you may require fire rated cable,
FT-4/CMR UL approved for in-wall installations.

Camera - Wall Mounted

Camera - Ceiling Mounted

Step 2 ... connecting devices

Splitter -
8 camera/
1 Power

Video to DVR
Channels 1-8

Video to Camera

Power to Camera

Power to DVR

Power to Cameras

Power

from 120V

DC Converter - 12V

AV Cable: BNC/

DC Power

(1 per Camera)

VGA to PC Monitor or TV

BNC to Security Camera Monitor

(Not included)

RJ45 Ethernet

to Router and

Internet

PTZ & Alarm
Connections
(Cameras not
included)

Follow this diagram to make device connections. Note, some devices are
not included with this kit. See “What’s in the Box” for included devices.

DVR Front Face

Connect Mouse &

USB Drive

RCA Audio In from Audio

Cameras or Powered

Microphone

(Not included)

RCA Audio Out to

Powered Speakers

(Not included)

Smartphone

through Mobile

Internet Setup

(Smartphone Not

included)

Step 3 ... system start up

Power On/Off

To power the system On/Off, connect the power cable to the DC 12V port on the rear

panel. Flip the toggle switch on in the back of the DVR. At startup, the system performs

a basic system check and runs an initial loading sequence. After a few moments, the

system loads a live display view.

Default Video Output

The default video output for the DVR system is VGA. If you connect a BNC

(CVBS) monitor on initial setup, you will need to use the mouse “Scroll Wheel”

to switch to the BNC output to be able to use the mouse. Roll the mouse “Scroll
Wheel” backward to go to BNC and forward to go to VGA. The REMARK screen
is shown on startup.
Password

ATTENTION: By default, passwords are disabled on the system. You do not need

to enter a password when accessing any system menus. However, for security

purposes, it is highly recommended to enable passwords on the system using

the Password Menu. See “Password” section for details on setting up passwords.
Click APPLY to access the menus or click EXIT to cancel password setup and
return to the LIVE VIEW screen.
Standby Mode

The system can also be put into Standby Mode. Power will remain to the system but

will not be recording. To start/stop Standby Mode:

1. Press and hold the POWER button on the front panel or remote control until the

prompt closes. The system enters standby mode. You can also enter Standby
mode through the Quick Access Menu. See below.

2. To exit standby mode, press and hold the POWER button on the front panel

or remote control until the system beeps. The system will begin powering up.

Main Menu Access

To open the Main Menu: Right-click anywhere on-screen to open the Quick Access

Menu and select MAIN MENU (mouse only), or press the MENU button on the remote

control or front panel of the system.

NOTE: If passwords are enabled on the system, you need to select your Device ID and enter the 6-digit numerical password to open

the Main Menu.

Main Menu

1. RECORD SEARCH: Search for recorded video on the system.

2. RECORD: Configure recording parameters (quality, resolution), set record

modes, and enable/disable audio recording. Note: Audio capable cameras (not

included) are required for audio recording on the system.

3. HDD: Display hard drive status and format the internal hard drive of the system.

4. BASIC: Open the Basic Setup Menu, which lets you set the system language,

date and time, device IDs and passwords, and configure display, audio and

video settings.

5. ADVANCED: Opens the Advanced Setup Menu. You can view system info, con-

figure alarm, PTZ, motion detect, maintenance, mobile, and network settings.

6. EXIT: Closes the Main Menu.
7. Displays information about the contents of the selected Main Menu icon.

User Login Menu

No HDD installed

NOTE: If there is no HDD
installed, or the HDD is
not recognized, or the
HDD is not formatted

it will display a red

H】

in the video

preview interface. You must format the
HDD in the DVR before first use. See:
Menu > HDD management > Format.
After formatting, the system will restart.

Main Menu

Quick Access Menu

Quick Access Menu
When using the mouse, use the Quick Access Menu to access several sys-
tem options, including the Main Menu. Select one of the following
options:
• MAIN MENU: Opens the main system menu
• KEYLOCK: Logs current user off the system. Re-login required.
• CHN SWITCH: Select type of split-screen display
• VIDEO SEARCH: Open the Search Menu to view recorded video
• PTZ : Opens the PTZ control menu
• MUTE: Mute listen-in audio on the system
• MANUAL REC: Start manual recording
• STOP REC: Stop manual recording
• ROTATION: Video rotation
• START CRUISE: Click to start preset PTZ Camera motion
• STOP CRUISE: Click to stop preset PTZ Camera motion
To close the Sub-Menu, click anywhere on-screen.

Main Viewing Screen

Showing No HDD in DVR

Switch between VGA to BNC Output

Advertising