First Alert 3040DF - Manual (Page 5)

Getting Started
3
STEP 4: Opening your Security
Box using the pre-set factory
code
THE PRE-SET FACTORY CODE IS 3 *
Using the keypad, enter the factory pre-set
code. The LED will flash a green light and
stay green for 10 seconds after the
button is pressed. You will hear the
Security Box unlock.
NOTE: You have 10 seconds to open the
Security Box. If the green light goes out,
you will have to re-enter the code.
To open, turn the knob from the locked
position to the unlocked position, one
quarter turn counter-clockwise. To open, lift
from the outer edge of the lid. (fig.2)
If the LED light flashes red after you enter
the code, this means the code was entered
incorrectly and the Security Box will not
open.
NOTE: If an incorrect code is entered 3
times in a row, the Security Box will
automatically shut down for 4 minutes
before it can be opened again using the
correct code. During this delay, the
Override Key can be used to open the
Security Box.
English
NOTE: For your security, immediately
re-program the digital lock to your
Personal Passcode.
Open your Security Box with the Override
Key or with the pre-set factory Passcode.
On the inside of the lid, find and press
the red button located to the side of the
battery compartment (Fig.3). The LED light
above the keypad will flash orange.
Enter your personal Passcode, up to 5
digits, followed by the button and then
repeat a second time. You must enter
the number twice.
For example: 1 2 3 4 5 - 1 2 3 4 5
After the first entry, the LED will flash orange.
After the second entry, the LED will flash
green and then go out.
Your Personal Passcode is now saved.
Write it down and store it in a secure place
away from the Security Box.
Close the lid of your Security Box and
return the knob to the locked position (Fig. 6).
If the override key was used, turn to the
locked position, remove and replace the
lock cover.
NOTE: The factory pre-set code is no longer active and cannot
be used to open the Security Box.
Programming your
Personal Passcode
STEP 1: Locate Override Keys
Keys and batteries are stored in the packing
material. Remove them before discarding
the box.
STEP 2: Opening your Security
Box using your Override Key
Remove cover from key lock.
Insert Override Key into key lock and turn
the key counter clockwise one quarter turn
to the unlocked position.
Turn the knob counter-clockwise one
quarter turn to the unlocked position. (fig.1)
To open, lift from the outer edge of the lid.
(fig.2)
STEP 3: Installing Batteries
Locate the battery cover on the back side
of the lid. (fig.4)
Slide the cover off the battery
compartment.
Properly insert batteries, noting correct
direction, replace cover and close the
Security Box lid.
Return the Override Key and the knob to
the locked position.
NOTE: Clean the battery contacts in the battery
compartment and on the batteries before
installing new batteries
4
2
5
3
*
1
10
Important
Bienvenue dans la gamme de produits
First Alert
® En plus de la tranquillité
d’esprit votre coffre numérique First Alert ®
vous permettra de conserver vos objets de
valeur en toute sécurité pendant bon nombre
d’années.
Pour une sécurité maximum, vous devriez:
Régler immédiatement votre propre code
personnel.
Ranger les clés et votre code personnel en
dehors du coffre.
Le code par défaut de votre coffre est:
3
*
Vue d’ensemble
10
8
4
1
5 2
6
3
9
1. Symbole de la fermeture par la clé de sécurité
2. Verrou à clé prioritaire
3. Bouton rotatif ou poussoir d’ouverture du verrou
4. Symbole du verrou ouvert
5. Voyant lumineux
6. Couvercle du coffre
7. Bouton de réglage du code rouge
(voir schéma sur la droite)
8. Symbole de la clé de sécurité non fermée
9. Symbole du verrou fermé
10. Touches du pavé numérique
11. Prise du trou de fixation du câble de sécurité
Français
+ +
7
Votre boîte de sécurité comprend
• (4) batteries "AA”
• (1) Éponge en mousse permettant
d’assurer une protection
ajoutée à vos objets de valeurs
• (2) Clés de priorité
• (1) Couvercle de la serrure de sécurité
• (1) Câble sécurisé en acier de 4 pieds
(3040DF, 3040DEF)
• (1) Fixation du câble de sécurité
Prise du trou
(3040DF, 3040DEF)
11