Fostex D2424LV - Manual (Page 16)

16
Model D2424LV Quick Operation Guide
Basic analog recording
1. Press the [RECORD TRACK] select key of the desired
recording track to set it in READY mode.
The “ ready ” track indicator (a small square) flashes on the
display.
Selecting a recording track
Adjusting the recording level
This recorder does not have any recording level
controls. You need to adjust the recording level on the
device that outputs recording data. Use the group
master faders on the mixer (faders that control the
output level of BUSS OUTs). Set the recording tracks
on this recorder to input monitoring status so that you
can check the level adjustment.
2.Press the [RECORD] button once. (The RECORD LED
flashes.)
The “ ready ” tracks enter the input monitoring status.
As you raise the group output level on the mixer, the level
meter segments of the ready tracks light up. Adjust the
level so that the “
0 ” to “ 3 ” level segments of the level meter
light up at the highest peak.
If the “OL” segments of the meter light up, the recording
level is too high. If the recording level is too high on a
digital recorder, the recording signal may distort, unlike
an analog recorder. Especially, if you are recording vocal
or acoustic instruments, the recording level may suddenly
peak.
In this case, you may want to lower the signal peak by
applying a compressor/limiter using an insertion connector.
3.Hold down the [RECORD] button and press the
[PLAY] button.
The flashing RECORD LED and the track indicator (a small
square) light up steadily.
Starting recording
4.Press the [STOP] button.
When the recorder section is stopped, the “ Please Wait! ”
message appears on the display momentarily, then the
current position appears. The ready track indicators flash.
Stopping recording
Playing the recorded tracks
<Undo and redo recording>
If you make a mistake or you are not satisfied with the
recording, you can “undo” recording. Refer to the “Undo
and redo recording” section below.
Flashing
The following explanation assumes that this recorder has been connected to an external mixing console (as explained
in the “Connecting a Mixer” section).
Because the D2424LV can accept 24 channel analog signals, you can record up to 24 audio sources simultaneously.
5.Press the [RECORD TRACK] select keys for the ready
tracks to set the tracks in the safe status.
The flashing track indicators turn off.
6. Hold down the [STOP] button and press the
[REWIND] button to locate the top of the Program
(ABS 0).
The top of the Program is immediately located in LOCATE
ABS 0 mode.
7.Press the [PLAY] button.
The playback starts from the top of the Program.
Adjust the level of input signal at TAPE IN on the mixer and
monitor the sound.
Repeat the procedure described above to record more tracks
(mono track or multiple tracks). You can record eight different
sound sources on this recorder simultaneously.
Basic recording
After you finish preparing a recording media and connecting a mixer, you can start basic recording
using this recorder.
F S M
∞ 42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
PGM
24
∞ 42
OL
0
30
24
18
12
9
6
3
ABS
23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
CLOCK
INT
POWER HOLD
RECORD STOP PLAY REW F FWD
ALL INPUT ALL READY
LOCATE REC END
VARI PITCH PUNCH LOCATE REHEARSAL
TAKE
RECALL STORE
EXIT/NO EXECUTE/YES PGM SEL
NEXT PREV UNDO/REDO
PREVIEW
EDIT SETUP
AUTO RTN
OUT IN AUTO PLAY START OUT IN END
17-24 ACCESS 9-16
1/9/17 2/10/18 3/11/19 4/12/20 5/13/21 6/14/22 7/15/23 8/16/24
FOOT SW
LOCATE ABS 0
CLIPBOARD PLAY
AUTO
TRACK SHIFT
SHIFT
DISP SEL
CHARACTER
TIME BASE SEL
P.EDIT
EJECT
ENVELOPE
CHASE
TC READY TC GEN M.UNDO
TRACK SHIFT
PREV TC NEXT TC
RECORD TRACK
CLIPBOARD AUTO PUNCH
AUTO RTN
LOCATE MEMORY
24bit 96kHz
OPTICAL
24TRACK DIGITAL RECORDER
1, 5 4 6
2 3 7