FUNAI BZV420MW8 - Manual (Page 30)

28 EN 28 EN
TIMER RECORDING
Hints for Timer Recording
When the starting time is the same:
A program set previously (PROG. A) has priority.
PROG. A
PROG. B
actual
recording
PROG. A PROG. B
The first 2 minutes (at the longest) will be cut off.
PROG. A
The Priority of Overlapped Settings
Note for DVD recording
• When the recording time of 2 programs are overlapped, or
the end time of a program and the start time of another
program is the same, the first 2 minutes (at the longest) of
the subsequent program will be cut off.
• If the cut-off portion comes up to 3 minute or more, this
program will be displayed with error number E40 in the
timer programming list.
PROG. A
PROG. B
actual
recording
The first 2 minutes (at the longest) will be cut off.
PROG. B PROG. A
When the end time of the programming
currently being recorded and the start time
of the subsequent program are same:
The beginning of the PROG. B may be cut off.
• If there is a power failure or this unit has been
unplugged for more than 30 seconds, the clock setting
and all timer programming will be lost.
• If a disc is not inserted, TIMER REC indicator on the front
panel flashes and timer recording cannot be performed.
In some cases, TIMER REC indicator will light up
momentarily around the start point as the unit attempts
to record. Please insert a recordable disc.
• If a cassette tape with a erase-protection tab is not in the
cassette compartment or there is no cassette tape in the
cassette compartment, VCR REC indicator on the front
panel flashes and timer recording cannot be performed.
Please insert a recordable cassette tape.
• If you press [TIMER SET] and turn on the unit while
either DVD or VCR is in timer standby mode (TIMER REC
indicator will light off). In this case, you cannot change
the mode between DVD and VCR. You cannot change
any settings using [SETUP] or edit discs.
• When all the timer recording is completed, TIMER REC
indicator flashes. To play back or eject the recorded disc,
press [TIMER SET] first, then select the recorded title
and press [PLAY B], or [OPEN/CLOSE A] to remove the
disc.
• If both DVD and VCR are timer programmed, you cannot
use any functions for either unit during timer standby or
timer recording. If you want to use functions other than
recording under such condition, cancel timer recording
by pressing [TIMER SET] during timer standby or stop
recording by pressing [STOP C] on the front panel
during timer recording.
• To cancel the timer standby mode, press [TIMER SET].
• When the starting and the ending time are the same, the
length of the recording will be set for 24 hours. When
the disc or cassette tape becomes full during the
recording, the unit turns itself off.
• When the programmed starting and ending time are
earlier than the current time, the setting will not be
accepted and be cleared for redoing.
• If the starting time is earlier and the ending time is later
than the current time, the recording will start right after
you turn the power off.
• The timer recording for digital TV cannot record any
audio language other than English.
• The timer recording cannot be performed in DVD and
VCR at the same time. If you set 2 programming with the
same channel and time in both devices, the program
with a lower program number will be recorded.
• Timer program which has the earlier start time will be placed first in the timer program list, and be given priority over
the programs with the later start time when timer programs overlap.
• When timer programs overlap, the first 2 minutes (at the longest) of the later recording will be cut off.
• When two or more timer programs have the same start time, the program set first will be given priority.
• A timer recording of lower priority will be canceled or start from the middle.
• Check the overlapped timer programmings and change the priority if necessary.
E9E2ZUD_BZV420MW8.indd 28 E9E2ZUD_BZV420MW8.indd 28 2007/09/04 17:05:43 2007/09/04 17:05:43