Gentek 710LS - Manual (Page 5)

3. Testing with the Test Knob:
a. Rotate the test knob counter-clockwise to the
TEST 1 position and wait up to 20 seconds for
the alarm to sound. If the alarm does not sound
after 20 seconds, return the alarm for service.
b. After successfully testing alarm, return test knob
to NORMAL (non-test) position and wait 20
seconds for the alarm to stop sounding.
c. To test alarm for high sensitivity, turn test knob
clockwise to test position 2. Alarm should
remain silent. Return knob back to the normal
position.
If your alarm sounds during this test it means the
alarm's sensitivity has become too high and may
cause false alarms.
This could mean your alarm is dirty and should be
cleaned as described in the maintenance
procedure below.
If the alarm continues to alarm for TEST 2 position
following cleaning return it to Gentex for service.
To check for proper smoke entry into your alarm's
sensing chamber. Gentex recommends using the
Home Safeguard Smoke Detector spray.
This test should be performed once a year and
should be sprayed from a distance no closer than
12 inches from smoke alarm.
IMPORTANT: The test knob is not an electrical switch, nor is it
connected in any way to the alarm. Therefore, when you test
with the test knob, you are actually simulating a smoke condition
in the alarm, as well as testing the sensitivity of the photodiode
and the circuit between the photodiode and the alarm.
MAINTENANCE
After your alarm has been in operation for a period of time or
if it was installed prior to the completion of all building
construction, your alarm may have become more sensitive due to
dirt build-up in the alarm's optic sensing chamber which could
cause nuisance alarms or could cause activation from small
amounts of smoke build-up.
·
If this should occur, following this simple washing
procedure will restore your smoke alarm back to its
original condition.
·
For further information, regarding frequency of cleaning
and testing, refer to NFPA 72, NFPA, Batterymarch Park,
Quincy, MA 02269.
IMPORTANT: Failure to follow full cleaning instructions
could result in damage to this smoke alarm.
DO NOT remove all alarms at the same time for cleaning.
1. Unplug the electrical power cord to the alarm.
2. Twist the alarm counter-clockwise to remove it from its
mounting plate.
3. Select three (3) standard size wash buckets and fill them
each with one gallon of normal tap water (distilled or
de-ionized treated water is recommended as a final rinse if
water is extremely hard in your area).
4. Add 1/8 cup of Ivory dishwashing liquid to the first bucket of
water and allow it to mix thoroughly, then place one dirty
alarm into the soap water mixture until it becomes
completely covered or submerged.
LIMITED WARRANTY
For a period of 12 months from the date of purchase, or a maximum of 18 months from
the date of manufacture, Gentex warrants to you, the original consumer purchaser, that
your Smoke Alarm will be free from defects in workmanship, materials, and construction
under normal use and service. If a defect in workmanship, materials, or construction
should cause your Smoke Alarm to become inoperable within the warranty period, Gentex
will repair your Smoke Alarm or furnish you with a new or rebuilt replacement Smoke Alarm
without charge to you except for postage required to return the Smoke Alarm to us. Your
repaired or replacement Smoke Alarm will be returned to you free of charge and it will be
covered under this warranty for the balance of the warranty period.
This warranty is void if our inspection of your Smoke Alarm shows that the
damage or failure was caused by abuse, misuse, abnormal usage, faulty installation,
improper maintenance, or repairs other than those performed by us.
ANY WARRANTIES IMPLIED UNDER ANY STATE LAW, INCLUDING IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
APPLY ONLY FOR THE WARRANTY PERIOD SPECIFIED ABOVE. PLEASE NOTE
THAT SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.
GENTEX WILL NOT BE LIABLE FOR ANY LOSS, DAMAGE, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND ARISING IN CONNECTION WITH THE
SALE, USE, OR REPAIR OF THIS SMOKE ALARM. PLEASE NOTE THAT SOME
STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES. SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.
If a defect in workmanship, materials, or construction should cause your Smoke Alarm
to become inoperable within the warranty period, you must return the Smoke Alarm to
Gentex postage prepaid. You must also pack the Smoke Alarm to minimize the risk of it
being damaged in transit. You must also enclose a return address. Smoke Alarms returned
for warranty service should be sent to: Gentex Corporation, 10985 Chicago Drive, Zeeland,
MI 49464.
If we receive a Smoke Alarm in a damaged condition as the result of shipping, we will
notify you and you must file a claim with the Shipper.
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY
ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
GENTEX CORPORATION
10985 CHICAGO DRIVE, ZEELAND, MI 49464
PHONE: 1-800-436-8391
550-0060-11
9-1-87
Pg. 7-5
NOTE: If the alarms are exceptionally dirty, you may wish
to first wipe off any excess dirt before washing alarm so as
not to dirty the wash water too quickly.
DO NOT open alarm for cleaning.
WARNING:
ONLY IVORY DISHWASHING LIQUID IS
TO BE USED. OTHER BRANDS ARE
NOT RECOMMENDED AND MAY CAUSE
YOUR ALARM TO MALFUNCTION.
5. Allow alarm to soak for approximately 10 minutes (longer if
extremely dirty). Then agitate for 5 or 10 seconds to flush
out any remaining dirt left inside alarm's housing.
6. Remove alarm from wash water and transfer directly to one
of the first rinse buckets containing clear water. Again, allow
alarm to become completely submerged, agitate once more
for 5 or 10 seconds to remove soap residue.
7. Finally, transfer alarm to your second and final rinse bucket,
repeating method found in Step 6, then remove alarm to a
clean dry area for a period of 48 hours to allow it to
thoroughly dry.
WARNING: SMOKE ALARMS ARE TO BE AIR DRIED ONLY.
DO NOT PLACE ALARM IN OVEN, MICROWAVE OR USE A
HOT AIR BLOWER TO ACCELERATE DRYING TIME. THIS
COULD RESULT IN DAMAGE TO YOUR SMOKE ALARM.
IMPORTANT: IT IS RECOMMENDED TO CHANGE WASH AND
RINSE WATER AFTER FIVE (5) ALARMS. IF YOUR ALARMS
ARE EXTREMELY DIRTY, WATER SHOULD BE CHANGED
MORE FREQUENTLY.
In the event you experience difficulty in the cleaning of your
smoke alarm or if you have any questions, please contact Gentex
Corporation or your local Gentex distributor.
WARNING:
If the smoke alarm does not work properly, do not try and fix it
yourself. This will void your warranty. See "To Return an Alarm"
for instructions to return smoke alarms that do not operate
properly. DO NOT TRY TO FIX IT YOURSELF.
IMPORTANT: Gentex recommends alarm be tested a
minimum of once a week.
WARNING: Never use an open flame of any kind to test your
alarm. You may ignite and damage the alarm as well as your
home. The test feature of your alarm accurately simulates smoke
conditions and tests the alarm's functions as required by
Underwriters Laboratories.
WARNING: Do not cover, tape, or otherwise block the
openings of your smoke alarm. These openings are designed to
allow air to pass through your smoke alarm, thus sampling the air
around the alarm.
FAILURE TO REGULARLY CLEAN THIS SMOKE ALARM WILL
RESULT IN FALSE ALARMS. A BUILD UP OF DUST CREATES
AN OBSCURATION THAT SIMULATES SMOKE. THIS MEANS
THE UNIT WILL GO INTO ALARM WITHOUT A FIRE
CONDITION.
TO RETURN AN ALARM
Should you experience problems with your smoke alarm, proceed
as follows:
1. Unplug the electrical power cord to the alarm.
2. Twist the alarm counter-clockwise to remove it from its
mounting plate.
3. Carefully pack (the manufacturer cannot be responsible for
consequential damage) and return to the manufacturer.
Include complete details as to exact nature of difficulties
being experienced and date of installation.
4. Return to: Gentex Corporation, 10985 Chicago Drive,
Zeeland, Michigan 49464. Prior to returning, call Gentex at
1-800-436-8391 to obtain a RMA Number from our return
department.