Generac Power Systems 005261-1 User Manual
Page 47
1
026915
2
NIPPLE CLOSE 3/4 X 1.375
2
075580
1
FLANGE FUEL INLET
3
0F6390B
1
REGULATOR ASSY 2.4L
4
039253
2
SCREW HHC M8-1.25 X 20 G8.8
5
022145
2
WASHER FLAT 5/16-M8 ZINC
6
022129
2
WASHER LOCK M8-5/16
7
045771
2
NUT HEX M8-1.25 G8 CLEAR ZINC
8
040173
2
CLAMP HOSE #5.5 .62-.62
9
0E8286
1
STREET EL 45D 1/2 NPT BRASS
10
026812
2
ELBOW 90D 3/4 NPT
11
0F8379
1
NIPPLE PIPE 3/4 NPT X 7
12
0F3869
1 (REF)
SWITCH PRESSURE GAS 5" RISE (INCLUDED WITH I/N 3)
13
057823
2
CLAMP HOSE #10 .56 - 1.06
14
059057
1
HOSE 3/4 ID SAE-30R2 (18” LG)
15
047527
1
BARBED STR 1/2 NPT X 3/4
16
0D1509
1
DECAL INLET PRESSURE
17 *
050279
1
DECAL FUEL INLET NG (NATURAL GAS APPLICATION)
050280
1
DECAL FUEL INLET LPG (LP VAPOR APPLICATION)
18
0F2119
1
O-RING 45.63 ID X 2.62 WIDTH
19
0E6586
1
GASKET BOSCH 32
20
0E4394
1
ACTUATOR BOSCH 40 GOVERNOR (45KW)
0E4395
1
ACTUATOR BOSCH 32 GOVERNOR (35KW)
21
040105
1
HOSE COOL 2 IN ID 20R4 (45KW)
057753B
1
HOSE 1.5 ID X 2 LG 20R4 (35KW)
22
0E6382B
1
VENTURI HOLDER W/40MM ACTUATOR (45KW)
0E6382C
1
VENTURI HOLDER W/32MM ACTUATOR (35KW)
23
0F7790E
1
VENTURI THROTTLE 26MM
24
0E7121
1
O-RING 47.625 ID X 2.38 WIDTH
25
089617
1 (REF)
BARBED STR 1/4 NPT X 1/4 MALE
26
022097
4
WASHER LOCK M6-1/4
27
046580
4
SCREW SHC M6-1.0 X 45 G12.9
28
035685
2
CLAMP HOSE #28 1.32-2.25
29
0F6155
1
HARNESS CPL FUEL JUMPER
30
047290
1
HOSE 3/8 ID SINGLE BRAID (18” LG)
31
030340
1
HOSE 1/4 ID SAE 30R7 (12” LG)
32
057823
2
CLAMP HOSE #10 .56-1.06
NOTES:
1.
REGULATOR (I/N 3) AS SHOWN IN ILLUSTRATION IS SET UP FOR
NATURAL GAS APPLICATION.
2.
TO CONFIGURE REGULATOR FOR LP VAPOR, SWITCH HOSE BARB,
HOSE CLAMP (I/N 13) AND HOSE (I/N 14) FROM “OUT-1” TO “OUT-2”.
REPLACE PIPE PLUG FROM “OUT-2” TO “OUT-1”. USE PIPE SEALANT
ON HOSE BARB AND PIPE PLUG. MAKE SURE TO KEEP PORTS FREE
FROM DEBRIS DURING RECONFIGURATION PROCESS.
3*. FOR LP VAPOR APPLICATION SUBSTITUE LPG FUEL INLET DECAL P/N
050280 FOR NG FUEL INLET DECAL P/N 050279 (ITEM17).
4 . WHEN SWITCHING FUEL TYPES, THE PROPER DIP SWITCH SITTINGS
MUST BE MADE TO THE CONTROL PANEL. SEE OWNERS MANUAL, FUEL
SECTION FOR MORE DETAILS.