Gemini PMX-03 - Manual (Page 5)

center position the kill function is not active, and the fre-
quency will not be killed. When you move the selected
KILL SWITCH to the bottom FLASH position and hold it
there, the frequency will be killed. Releasing the selected
KILL SWITCH from the bottom position will bring it back
to the center position and the frequency will no longer be
killed.
5. CROSSFADER SECTION: The CROSSFADER (21)
allows the mixing of one source into another. The left side
of the CROSSFADER (21) is CHANNEL 1 and the right
side is CHANNEL 2. The CROSSFADER (21) in your
unit is removable and if the need arises can be easily
replaced. Your Gemini mixer comes with an RG-45 PRO
(RAILGLIDE™) Dual-Rail Crossfader. Rail Glide™ cross-
faders have internal dual stainless steel rails that allow the
slider to ride smoothly and accurately from end to end.
Also available is our CF-45 PRO (PROGLIDE™) Dual-
Rail Crossfader. This unique crossfader features, state of
the art conductive plastic technology, for unlimited useage.
Another crossfader we have available is the PSF-45 (PRO
SCRATCH™) crossfader with a special curve designed for
scratch mixing. Just purchase one from your Gemini
dealer and follow the instructions:
Note: Do not apply pressure while using the Crossfader. Lightly
glide the Crossfader back and forth. Pressing down on the controls
can bend contacts and cause a loss of sound.
6. CURVE CONTROL: The CROSSFADER CURVE
SWITCH (12) allows you to adjust the kind of curve the
crossfader has. Depress the crossfader curve button to
make the curve steep and cutting (perfect for scratching).
Release the crossfader curve button to make the curve
gradual and gentle.
7. HAMSTER CONTROL: The CROSSFADER
REVERSE SWITCH (11) allows you to reverse the cross-
fader so that CHANNEL 2 (31) is controlled by the left
side of the crossfader and CHANNEL 1 (19) is controlled
by the right side of the crossfader.
NOTE: When the CROSSFADER REVERSE SWITCH (11) is activated
(moved to the right), only the crossfader reverses. The Channel
Slides, Gain, Kill Switches and tonal controls do not reverse.
8. CUE: Cue facilitates the seamless blending of one
recorded track into another. Connecting a set of head-
phones to the HEADPHONES (8) jack allows you to moni-
tor either Channel 1 or Channel 2. Select CHANNEL 1
(19) by moving CUE FADER (18), located on the front
panel, to CUE 1 on the left. Listen to Channel 2 by mov-
ing CUE FADER (18) to CUE 2 on the right. To mix both
Channels bring CUE (18) to the middle so that both tracks
may be heard. Use CUE VOLUME (9) to adjust the head-
phone volume without affecting the speaker-driven mix.
09. MIC SECTION: Connecting a microphone to the 1/4"
MIC JACK (10) allows voice amplification through the
mixer to the stereo through the MASTER RCA OUTPUTS
(3) . This is controlled by the MIC VOLUME (16), HIGH
(15), LOW (14) rotary controls.
10. OUTPUT CONTROL SECTION: The level of the
MASTER OUTPUT (3) is controlled by the MASTER
VOLUME (13) rotary control.
11. VU METER: The VU METER (25) LEDs indicates the
MASTER RCA OUTPUT (3) in stereo. VU METER (25)
LEDs reflect the VOLUME (13), GAIN (24,32), HIGH
(23,33), MID (22,34) and LOW (21,35) rotary control
adjustments for each channel. The CHANNNEL SLIDES
(19, 31) also affect each of the VU METER (25) LEDs.
SPECIFICATIONS:
INPUTS:
DJ Mic......................................................................1.5 mV 1 kOhm Balanced
Phono.......................................................................................3 mV 47 kOhm
Line.......................................................................................150 mV 10 kOhm
OUTPUTS:
Amp........................................... .........................................0 dB 1V 400 Ohm
Max.....................................................................................20V Peak to Peak
GENERAL:
Bass (Channels 1-2)....................................................................+12dB/-36dB
Mid (Channels 1-2)......................................................................+12dB/-36dB
High (Channels 1-2)....................................................................+12dB/-36dB
Gain (Channels 1-2)........................................................................0 to -20 dB
Frequency Response....................................................20 Hz-20 kHz +/- 2 dB
Distortion...............................................................................Less Than 0.02%
S/N Ratio.............................................................................Better Than 80 dB
Headphone Impedance.......................................................................32 Ohm
Power Source Adapter........................................................115V/15V AC 0.5A
........................................................................................or 230V/15V AC 0.5A
Unit Dimensions........................................................W 10" x H 3.3" x D 10.25"
..........................................................................................(254 x 84 x 260mm)
Weight....................................................................................6.2 lbs ( 2.81 kg)
NOTE: SPECIFICATIONS AND DESIGN ARE SUBJECT TO CHANGE
WITHOUT NOTICE FOR PURPOSE OF IMPROVEMENT.
1. Unscrew the outside mixer
FACE PLATE screws and remove
the face plate. Then remove
FADER plate screws (B & C).
2. Carefully lift the fader and
unplug the CABLE (D).
3. Plug the new fader into the
cable and place it back in the
mixer.
4. Screw fader plate to the mixer
and replace the mixer FACE
PLATE.
USER REPLACEABLE CROSS FADER
(5)