MITSUBISHI ELECTRIC HC5500 User Manual
Page 5
5
ITEM
ASCII
HEX
VALUE
LENS SHIFT RESET
LSRST
4Ch 53h 52h 53h 54h
ASPECT
SC
53h 43h
0 (AUTO), 1 (4:3), 2 (16:9), 3 (ZOOM1), 4 (ZOOM2),
5 (STRETCH), 6 (ANAMORPHIC1), 7 (ANAMORPHIC2)
PASSWORD FUNCTION
PSLOCK
50h 53h 4Ch 4Fh 43h
4Bh
0**** (UNLOCK), 1**** (DISPLAY INPUT),
2**** (MENU ACCESS)
**** is a 4 to 8-digit password comprised of any fi gures 1 to 4.
MENU POSITION
MP
4Dh 50h
0 (Upper left), 1 (Lower right)
CINEMA MODE
CINE
43h 49h 4Eh 45h
0 (VIDEO), 1 (AUTO), 2 (FILM)
VIDEO SIGNAL
(VIDEO only)
VS
56h 53h
0 (AUTO), 1 (NTSC), 2 (PAL), 3 (SECAM), 4 (4.43NTSC),
5 (PAL-M), 6 (PAL-N), 7 (PAL-60)
SET UP
STU
53h 54h 55h
0 (AUTO), 1 (OFF), 2 (3.75%), 3 (7.5%)
SCART INPUT
SRT
53h 52h 54h
0 (OFF), 1 (ON)
LANGUAGE
LG
4Ch 47h
0 (
), 1 (English), 2 (Español), 3 (Deutsch), 4 (Français),
5 (Italiano), 6 (
), 7 (
), 8 (
), 9 (PORTUGUÊS)
RESET ALL
RSTALL
52h 53h 54h 41h 4Ch 4Ch
HORIZ.POSITION
HP
48h 50h
+: increment, -: decrement
*1
VERT.POSITION
VP
56h 50h
+: increment, -: decrement
*1
FINE SYNC.
FN
46h 4Eh
00–31
TRACKING
TRK
54h 52h 4Bh
+: increment, -: decrement
*1
COMPUTER INPUT
CIN
43h 49h 4Eh
0 (RGB), 1 (YC
B
C
R
/YP
B
P
R
), 2 (AUTO)
OVER SCAN
VOS
56h 4Fh 53h
00 (90%) – 10 (100%)
HOLD
HLD
48h 4Ch 44h
0 (OFF), 1 (ON)
HOLD BEGIN
HLB
48h 4Ch 42h
00–99
HOLD END
HLE
48h 4Ch 45h
00–99
CLAMP POSITION
CLP
43h 4Ch 50h
001–255
CLAMP WIDTH
CLW
43h 4Ch 57h
01–63
VERT.SYNC.
VSC
56h 53h 43h
0 (OFF), 1 (AUTO)
LPF
LPF
4Ch 50h 46h
0 (OFF), 1 (ON)
SHUTTER(U)
SHU
53h 48h 55h
00–32
SHUTTER(L)
SHL
53h 48h 4Ch
00–32
SHUTTER(LS)
SHLS
53h 48h 4Ch 53h
00–95
SHUTTER(RS)
SHRS
53h 48h 52h 53h
00–95
*1) Setting range differs depending on the input signals.
• Some commands are not executed depending on the input signal. The operational restrictions same as those
on the menu setting are applied. Refer to “Menu operation” in the User Manual for more details.
How to set the value
Use the ASCII or HEX code as shown below to set the value.
ASCII
‘+’
‘-’
‘0’
‘1’
‘2’
‘3’
‘4’
‘5’
‘6’
‘7’
‘8’
‘9’
HEX
2Bh
2Dh
30h
31h
32h
33h
34h
35h
36h
37h
38h
39h
[Example 1] When setting the AUTO POWER ON to ON. (Figures and symbols enclosed in quotation marks are
ASCII codes.):
Sending commands
from the PC, etc.
Status code
from the projector
Description
30 30 41 50 4F 4E 31 0D
‘0’ ‘0’ ‘A’ ‘P’ ‘O’ ‘N’ ‘1’ ‘ ’
Command for setting the AUTO
POWER ON to ON
30 30 41 50 4F 4E 31 0D
‘0’ ‘0’ ‘A’ ‘P’ ‘O’ ‘N’ ‘1’ ‘ ’
Command receipt confi rmation
(Command echo back)
[Example 2] When setting the CONTRAST R of the COLOR TEMP.-USER to +10, the CONTRAST G to 0, and the
CONTRAST B to -5. (Figures and symbols enclosed in quotation marks are ASCII codes.):
Sending commands
from the PC, etc.
Status code
from the projector
Description
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D
‘0’ ‘0’ ‘P’ ‘+’ ‘1’ ‘0’ ‘+’ ‘0’ ‘0’ ‘-’ ‘0’ ‘5’ ‘ ’
Command for setting the picture
control
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D
‘0’ ‘0’ ‘P’ ‘+’ ‘1’ ‘0’ ‘+’ ‘0’ ‘0’ ‘-’ ‘0’ ‘5’ ‘ ’
Command receipt confi rmation
(Command echo back)