MTX Audio 600WM - Manual (Page 3)

OTHER BLUEPRINT SERIES PRODUCTS FROM MTX
MTX offers a wide assortment of audio components. Ranging from in-wall speakers to
amplifiers to accessories. Each component is value engineered and must meet strict
quality control standards before it becomes part of the MTX product line.
Listed below you will find a sampling of MTX components available from your autho-
rized Blueprint Series dealer.
IN-WALL LOUDSPEAKERS
MODEL 520W
5-1/4” Two-Way In-Wall Speaker
1” Soft Dome Tweeter
8 Ohm Impedance/84dB Sensitivity
53Hz-20kHz Frequency Response
50 Watts RMS/160 Watts Total
11”H x 7-1/2”W x 2-1/2”D
MODEL 620W
6-1/2” Two-Way In-Wall Speaker
1” Soft Dome Tweeter
8 Ohm Impedance/85dB Sensitivity
43Hz-20kHz Frequency Response
55 Watts RMS/180 Watts Total
12-1/16”H x 8-9/16”W x 2-7/8”D
MODEL 820W
8” Two-Way In-Wall Speaker
1” Soft Dome Tweeter
8 Ohm Impedance/86dB Sensitivity
33Hz-20kHz Frequency Response
60 Watts RMS/200 Watts Total
14-1/16”H x 10-1/16”W x 3-1/2”D MODEL 502W
5-1/4” Two-Way In-Wall Speaker
1/2” Polycarbonate Dome Tweeter
8 Ohm Impedance/84dB Sensitivity
53Hz-20kHz Frequency Response
45 Watts RMS/140 Watts Total
11”H x 7-1/2”W x 2-1/2”D
MODEL 602W
6-1/2” Two-Way In-Wall Speaker
1/2” Polycarbonate Dome Tweeter
8 Ohm Impedance/85dB Sensitivity
43Hz-20kHz Frequency Response
50 Watts RMS/160 Watts Total
12-1/16”H x 8-9/16”W x 2-7/8”D
SPEAKER/AMPLIFIER SELECTOR
LPS-600
Accommodates up to 6 pair of speakers
Handles up to 250 Watts/channel continuous (RMS)
Impedance Protection Circuitry
Low profile-full size component
Two-piece, plug in connectors on the rear panel
Accommodates up to 14 gauge wire
TV-5 UL Approved Switches
A/B Amplifier and Input Selector
ACCESSORIES
VC-30B/VC-30W
Decora-Style Volume Control (Bone or White)
10 Step 25 Watts per channel (RMS) 150 Watts Peak
AB-1SB/AB-1SW
Decora-Style A/B Switch (Bone or White)
PCK65C
Pre-Construction Kit for Model 610RCM
PCK85C
Pre-Construction Kit for Model 810RCM
LOUDSPEAKER PLACEMENT
MTX In-Walls can be positioned virtually anywhere you desire sound. Important
considerations are room layout, furniture arrangement, location of audio/video
equipment and daily foot traffic within the room/house. MTX In-Walls are
designed to be installed between wall studs, so avoid locations next to doors,
windows or other construction that may present difficulties. If used for video, In-
Walls should be placed at least six feet away from your video screen, to avoid
magnetic interference.
THE MODEL 600WM WATER RESISTANT LOUDSPEAKER
The MODEL 600WM is specifically designed for use in areas where moisture is
present, such as bath, sauna, hot tub area, patio, poolside and other exterior appli-
cations. If you are planning an installation of this type, we strongly recommend
the MODEL 600WM Water Resistant Loudspeaker.
Drop ceiling wiring example Baseboard/carpet wiring
example
Exterior soffit example
Attic wiring example Basement wiring example