Preparation, En - 13 – MITSUBISHI ELECTRIC XD450U User Manual

Page 13

Advertising
background image

EN - 13

ENGLISH

Preparation

1. Tilt up the project to the appropriate angle.

2. Press the foot adjustment buttons next to the adjust-

ment feet (rear), and the adjustment feet will come

out.

3. Release the buttons to lock the adjustment feet (rear)

to that position.

4. Rotate the adjustment feet (rear) for fine adjustment.
After using the projector:

5. Put the adjustment feet (rear) back into the projector

by pressing the foot adjustment buttons.

Important:

• If necessary, rotate the adjustment feet (front) for fine

adjustment.

• Install the screen on a flat wall at 90 degrees to the

floor.

• Slanting the projector more than ±10º (horizontally)

or ±15º (vertically) may cause trouble or explosion of

the lamp. You can tilt the projector up to 7 degrees

using the adjustment feet only.

• Images may not be projected in a shape of a regular

rectangle or with its aspect ratio 4:3, depending on

the installation conditions of the projector and the

screen.

• To correct vertical and horizontal keystone distortion,

press the KEYSTONE button on the projector or the

remote control to display KEYSTONE, and adjust the

image by pressing the , , ,  button (or VOL-

UME +, - button on the remote control).

In the following cases:

Preparation for projection

1. Attach the provided power cord to the projector.

2. Plug the power cord in the wall outlet.

3. Remove the lens cap.
Warning:

• Do not look into the lens directly when the projector is

on.

• The lens cap is for protecting the lens. If you leave

the lens cap on the lens with the projector turned

on, it may be deformed because of heat build-up.

Remove the lens cap when you turn on the projector.

• The power cords for use in the U.S. and Europe are

provided with this projector. Use the appropriate

cord for your country.

• This projector uses the power plug of three-pin

grounding type. Do not remove the grounding pin

from the power plug. If the power plug doesn't fit

your wall outlet, ask an electrician to change the wall

outlet.

• The provided power cord for the U.S. is rated at 120 V.

Never connect this cord to any outlet or power sup-

ply using other voltages or frequencies than rated. If

you want to use a power supply using other voltage

than rated, prepare an appropriate power cord sepa-

rately.

• Use 100-240 V AC 50/60 Hz to prevent fire or elec-

tric shock.

• Do not place any objects on the power cord or do

not place the projector near heat sources to prevent

damage to the power cord. If the power cord should

be damaged, contact your dealer for replacement

because it may cause fire or electric shock.

• Do not modify or alter the power cord. If the power

cord is modified or altered, it may cause fire or elec-

tric shock.

Caution:

• Plug in the power cord firmly. When unplugging, hold

and pull the power plug, not the power cord.

• Do not plug in or out the power cord with your hand

wet. It may cause electric shock.

Adjustment of the projection angle

For the best projection, project images on a flat screen

installed at 90 degrees to the floor. If necessary, tilt the

projector using the two adjustment feet on the bottom

of the projector.

Important:

• You can correct the vertical and horizontal keystones

at the same time. However, their adjustment ranges

are limited in such correction.

• When the keystone adjustment is carried out, the

adjustment value is indicated. Note that this value

doesn't mean a projection angle.

• The allowable range of the adjustment value in the

keystone adjustment varies depending on the instal-

lation conditions.

• When the keystone adjustment takes effect, the res-

olution decreases. In addition, stripes may appear or

straight lines may bend in images with complicated

patterns. They are not due to product malfunctions.

• Noise may appear on the screen during the keystone

adjustment because of the type of the video signal

being projected and the setting values of the key-

stone adjustment. In such cases, set the keystone

adjustment values in the range where the image is

displayed without noise.

• When the keystone adjustment is carried out, the im-

age may not be displayed correctly because of the

type of input signal.

• When the 1080i signal is input, the keystone adjust-

ment ranges are limited.

Screen

Adjustment feet (Rear)

Press the 

button.

Press the 

button.

Press the 

(or -) button.

Press the 

(or +) button.

Advertising