Document Outline

• ENGLISH
• SPECIFICATIONS
• Model
• BFR540
• BFR550
• BFR750
• Screw strip
• 4 x 25 - 55 mm
• 4 x 45 - 75 mm
• No load speed (min-1)
• 4,000
• Overall length
• 424 mm
• 464 mm
• Net weight
• 2.1 kg
• 2.3 kg
• 2.3 kg
• Rated voltage
• D.C. 14.4 V
• D.C. 18 V
• D.C. 18 V
• Standard battery cartridges
• BL1430
• BL1830
• • Due to our continuing programme of research and developmen
• • Note: Specifications may differ from country to country.
• END004-1
• Symbols
• The following show the symbols used for the equipment. Be su
• ･ Read instruction manual.
• ･ Only for EU countriesDo not dispose of electric equipment
• ENE033-1
• Intended useThe tool is intended for screw driving in wood,
• For Model BFR540
• ENG101-1
• For European countries onlyNoiseThe typical A-weighted noi
• Sound pressure level (LpA) : 77 dB(A)
• Uncertainty (K) : 3 dB(A)
• The noise level under working may exceed 85 dB (A).
• Wear ear protection.
• ENG204-1
• Vibration
• The vibration total value (tri-axial vector sum) determined
• Work mode: screwdriving without impact
• Vibration emission (ah) : 2.5 m/s2 or less
• For Model BFR550
• ENG101-1
• For European countries onlyNoiseThe typical A-weighted noi
• Sound pressure level (LpA) : 78 dB(A)
• Uncertainty (K) : 3 dB(A)
• The noise level under working may exceed 85 dB (A).
• Wear ear protection.
• ENG204-1
• Vibration
• The vibration total value (tri-axial vector sum) determined
• Work mode: screwdriving without impact
• Vibration emission (ah) : 2.5 m/s2 or less
• For Model BFR750
• ENG101-1
• For European countries onlyNoiseThe typical A-weighted noi
• Sound pressure level (LpA) : 76 dB(A)
• Uncertainty (K) : 3 dB(A)
• The noise level under working may exceed 85 dB (A).
• Wear ear protection.
• ENG204-1
• Vibration
• The vibration total value (tri-axial vector sum) determined
• Work mode: screwdriving without impact
• Vibration emission (ah) : 2.5 m/s2 or less
• ENH102-6
• EC-DECLARATION OF CONFORMITY
• Model; BFR540, BFR550, BFR750
• We declare under our sole responsibility that this product i
• EN60745, EN55014 in accordance with Council Directives, 2004
• CE2006
• 000230
• Tomoyasu Kato
• Director
• Responsible Manufacturer:Makita Corporation3-11-8, Sumiyos
• Authorized Representative in Europe:Makita International Eu
• GEA002-3
• GENERAL SAFETY RULES
• WARNING! Read all instructions. Failure to follow all instru
• SAVE THESE INSTRUCTIONS.
• Work area safety
• 1. Keep work area clean and well lit. Cluttered and dark are
• 2. Do not operate power tools in explosive atmospheres, such
• 3. Keep children and bystanders away while operating a power
• Electrical Safety
• 4. Power tool plugs must match the outlet. Never modify the
• 5. Avoid body contact with earthed or grounded surfaces such
• 6. Do not expose power tools to rain or wet conditions. Wate
• 7. Do not abuse the cord. Never use the cord for carrying, p
• 8. When operating a power tool outdoors, use an extension co
• Personal Safety
• 9. Stay alert, watch what you are doing and use common sense
• 10. Use safety equipment. Always wear eye protection. Safety
• 11. Avoid accidental starting. Ensure the switch is in the o
• 12. Remove any adjusting key or wrench before turning the po
• 13. Do not overreach. Keep proper footing and balance at all
• 14. Dress properly. Do not wear loose clothing or jewellery.
• 15. If devices are provided for the connection of dust extra
• Power tool use and care
• 16. Do not force the power tool. Use the correct power tool
• 17. Do not use the power tool if the switch does not turn it
• 18. Disconnect the plug from the power source and/or the bat
• 19. Store idle power tools out of the reach of children and
• 20. Maintain power tools. Check for misalignment or binding
• 21. Keep cutting tools sharp and clean. Properly maintained
• 22. Use the power tool, accessories and tool bits etc. in ac
• Battery tool use and care
• 23. Ensure the switch is in the off position before insertin
• 24. Recharge only with the charger specified by the manufact
• 25. Use power tools only with specifically designated batter
• 26. When battery pack is not in use, keep it away from other
• 27. Under abusive conditions, liquid may be ejected from the
• SERVICE
• 28. Have your power tool serviced by a qualified repair pers
• 29. Follow instruction for lubricating and changing accessor
• 30. Keep handles dry, clean and free from oil and grease.
• GEB017-1
• SPECIFIC SAFETY RULES
• DO NOT let comfort or familiarity with product (gained from
• 1. Hold power tools by insulated gripping surfaces when perf
• 2. Always be sure you have a firm footing.Be sure no one is
• 3. Hold the tool firmly.
• 4. Keep hands away from rotating parts.
• 5. Do not touch the bit or the workpiece immediately after o
• SAVE THESE INSTRUCTIONS.
• WARNING:
• MISUSE or failure to follow the safety rules stated in this
• ENC007-2
• IMPORTANT SAFETY INSTRUCTIONS
• FOR BATTERY CARTRIDGE
• 1. Before using battery cartridge, read all instructions and
• 2. Do not disassemble battery cartridge.
• 3. If operating time has become excessively shorter, stop op
• 4. If electrolyte gets into your eyes, rinse them out with c
• 5. Do not short the battery cartridge:
• (1) Do not touch the terminals with any conductive material.
• (2) Avoid storing battery cartridge in a container with othe
• (3) Do not expose battery cartridge to water or rain.A batt
• 6. Do not store the tool and battery cartridge in locations
• 7. Do not incinerate the battery cartridge even if it is sev
• 8. Be careful not to drop or strike battery.
• SAVE THESE INSTRUCTIONS.
• Tips for maintaining maximum battery life
• 1. Charge the battery cartridge before completely discharged
• 2. Never recharge a fully charged battery cartridge.Overcha
• 3. Charge the battery cartridge with room temperature at 10ﾟ
• FUNCTIONAL DESCRIPTION
• CAUTION:
• Always be sure that the tool is switched off and the battery
• Installing or removing battery cartridge
• 006801
• Always switch off the tool before insertion or removal of th
• To remove the battery cartridge, withdraw it from the tool w
• To insert the battery cartridge, align the tongue on the bat
• Do not use force when inserting the battery cartridge. If th
• Setting for desired screw length
• 008123
• There are 7 positive-lock screw length settings. To obtain t
• For Models BFR540, BFR550
• 008238
• For Model BFR750
• 008241
• Adjusting the driving depth
• 008124
• Depress the stopper base as far as it will go. While keeping
• Switch action
• 008282
• CAUTION:
• Before inserting the battery cartridge into the tool, always
• To start the tool, simply pull the switch trigger. Release t
• Reversing switch action
• 008283
• This tool has a reversing switch to change the direction of
• When the reversing switch lever is in the neutral position,
• CAUTION:
• Always check the direction of rotation before operation.
• Use the reversing switch only after the tool comes to a comp
• When not operating the tool, always set the reversing switch
• ASSEMBLY
• CAUTION:
• Always be sure that the tool is switched off and the battery
• Installing or removing the bit
• Loosen the thumb screws which secure the casing. Pull out th
• 008285
• Press the dust cover toward the plane bearing and pull out t
• 008286
• Installing screw strip
• Insert the screw strip through the screw guide. Then insert
• 008290
• 008288
• Removing screw strip
• To remove the screw strip, just pull it out in the direction
• 008281
• 008128
• Folding screw guide
• 008289
• Screw guide is foldable. Folding the screw guide allows spac
• Carry hook
• The carry hook is convenient for temporarily hooking the too
• 008262
• OPERATION
• Driving operation
• 008263
• Switch on the tool by pulling the switch trigger. Hold the t
• CAUTION:
• Always check the bit carefully for wear before driving opera
• Always hold the tool squarely against the driving surface. H
• Always keep the tool firmly against the driving surface unti
• Be careful not to drive a screw onto another screw already f
• Do not operate the tool without screws. It will damage the d
• Do not apply oil or grease on the sliding surface of the fee
• Driving in corner
• 006812
• This tool can be used to drive at a position 15 mm away from
• CAUTION:
• Driving at a position closer than 15 mm to the wall or driv
• MAINTENANCE
• CAUTION:
• Always be sure that the tool is switched off and the battery
• Replacing carbon brushes
• 006258
• Replace when they wear down to the limit mark. Keep the carb
• Loosen the thumb screws which secure the casing. Pull out th
• 008285
• Use a screwdriver to remove two screws then remove the front
• 008287
• Raise the arm part of the spring and then place it in the re
• 006816
• Use pliers to remove the carbon brush caps of the carbon bru
• 006817
• Make sure that the carbon brush caps have fit into the holes
• 006304
• Reinstall the front cover and tighten two screws securely.
• To maintain product SAFETY and RELIABILITY, repairs, any oth
• ACCESSORIES
• CAUTION:
• These accessories or attachments are recommended for use wit
• If you need any assistance for more details regarding these
• Drywall screw strip
• Phillips bit
• Various type of Makita genuine batteries and chargers
• Plastic carrying case