Marantz MV5100 - Manual (Page 40)

ONE TIME PROGRAM
PROGRAM 1
CHANNEL +/– – – –
START +/–
– – : – – AM
STOP +/– – – : – – AM
REC SPEED SLP
DATE +/– – – /– – /– –
DAILY: 8 WEEKLY: 9
CONFIRM: OK
END: TIMER
Follow the steps below to program your VCR to record TV pro-
grams while you’re away from home.The VCR will turn itself on,
record, and turn itself off automatically.
Before you begin, make sure:
• Channels are programmed. Details are on pages 12-13.
• The clock is set. Details are on pages 14-18. If the clock is not set,
CLOCK MUST BE SET appears on the screen, followed by the
menu.
• There is a tape in the VCR. Make sure the tape’s record tab is
intact and the tape is long enough to record the program(s).
• The VCR is in VCR position.The VCR light will appear on the dis-
play panel when the VCR is in VCR position. If the VCR light does
not appear, press the VCR/TV button once.
• When you use a Cable Box/DBS, timer recordings are pro-
grammed differently. Read pages 8-9 before proceeding.
Complete each step within 60 seconds of the previous step.
1
Press the VCR button, then press the TIMER button.
2
Press the PLAY 8 or STOP 9 button to select QUICK
PROGRAMMING, then press the OK/STATUS button.
3
Press the CH(annel) 8/9 button to enter the channel you
want to record.
• If you are using a standard antenna/cable to VCR to TV hookup (as
shown on pages 6-7), enter the channel of the TV program you
want to record.
• If you are using a Cable Box/DBS and are not using the Controller,
enter the Cable Box/DBS output channel (03 or 04). Set the Cable
Box/DBS to the channel you want to record. Leave the Cable
Box/DBS on for a timer recording.
• If you are using the Controller, enter the channel number that you
want to record.The Controller will select the channel at the Cable
Box/DBS.
→ VCR PLUS+
QUICK PROGRAMMING
PROGRAM REVIEW
SELECT: ,9 CONFIRM: OK
END: TIMER
ONE TIME PROGRAM
PROGRAM 1
CHANNEL +/– 12 CABLE/TV
START +/– – – : – – AM
STOP +/– – – : – – AM
REC SPEED SLP
DATE +/– – – /– – /– –
DAILY: 8 WEEKLY: 9
CONFIRM: OK
END: TIMER
1
1
3
2
40 Quick Programming
• If you are using a DBS with the
Controller, CABLE/TV or DBS appears
beside the channel number.You may
need to clarify whether the desired
channel is for Cable TV or Satellite TV
(DBS). If so,“CABLE/TV OR DBS: 0”
will appear at the bottom of the
screen. Press the Number 0 (DBS)
button to select either CABLE/TV or
DBS. Press the button repeatedly to
switch between the CABLE/TV and
DBS settings.
CABLE/TV is to record a cable TV pro-
gram received on the VCR or through
a Cable Box; DBS is to record a satel-
lite program received through a DBS.
Helpful Hint
ONE TIME PROGRAM
PROGRAM 1
CHANNEL +/– 125 DBS
START +/– – – : – – AM
STOP +/– – – : – – AM
REC SPEED SLP
DATE +/– – – /– – /– –
CABLE/TV OR DBS: 0
CONFIRM: OK
END: TIMER
VCR TV
VCR/TV
QUICK PROGRAMMING
POWER
STILL/SLOW
SMARTPICTURE
CH VOL
MENU
TIMER
JOG/SHTL
TURBO
TIMER
AUDIO/
MUTE
SKIP
SEARCH
TAPE
MANAGER
OK/STATUS
- .......... .......... +
CBL/DBS
1 – + * 2 ABC 3 DEF
4 GHI 5 JKL 6 MNO
7 PQRS 8 TUV 9 WXYZ
START STOP DATE
VPS/PDC DAILY
SPEED DBS/SAT
PLAY
REW FF
STOP
WEEKLY
/OTR REC
-
+
-
+
ALT 0 CLEAR
SAT/
REV FWD
MV5100 27-84 7/21/00 10:59 AM Page 40