Master Chef T360 - Manual (Page 4)

4 5
LP Cylinder Leak Test For Your Safety
ATTENTION: Leak Test must be repeated each time the LP cylinder is exchanged or refilled.
• Do not smoke during leak test.
• Do not use an open flame to check for gas leaks
• BBQ must be leak tested outdoors in a well ventilated area, away from ignition
sources such as gas fired electrical appliances. During leak test, keep your BBQ
away from open flames or sparks.
º Use a clean paint brush and a 50/50 mild soap and water mixture.
º Brush soapy solution onto areas indicated by arrows in figure A.
DO NOT USE HOUSEHOLD CLEANING AGENTS:
Damage to gas train components can result.
WARNING
If growing bubbles appear do not use or move the LP cylinder. Contact an LP gas supplier or your
fire department.
Propane Models:
Your Barbecue is designed to operate on L.P gas at a pressure of 2.74Kpa (11” water column). A regulator preset to this
pressure is supplied with
your Barbecue.
Hose and Regulator comes equipped with the following:
Type 1 quick closing connection system which incorporates the following
safety features:
• Will limit the gas flow until a POSITIVE CONNECTION has been made
• Has a THERMAL COMPONENT that will automatically shut off the flow of gas
if a temperature of 115-150°C (240-300°F) is reached.
• Has a Flow Limiting Feature, which will restrict the flow of gas to 10 cubic ft/ hour
in the event of a leak, improper lighting procedure, or regulator malfunction.
Connecting Regulator to the LP Cylinder
1. LP cylinder must be properly secured onto grill.
2. Turn all control knobs to the OFF position.
3. Turn LP cylinder OFF by turning hand-wheel clockwise to a full stop.
4. Remove the protective cap from LP cylinder valve. Always use cap and strap
supplied with valve.
5. Hold regulator and insert nipple into LP cylinder valve. Hand tighten the
coupling nut. Hold the regulator in a straight line with LP cylinder valve so
as not to cross-thread the connection.
6. Turn the coupling nut clockwise and tighten to a full stop. The regulator will seal
on the back-check feature in the LP cylinder valve, resulting in some resistance.
NOTE:
If you cannot complete the connection, disconnect regulator and repeat
steps 5 and 6. If you are still unable to complete the connection, do not
use this regulator!
DANGER
Do not insert any tool or foreign object into the valve outlet or safety relief valve. You may damage the
valve and cause a leak. Leaking propane may result in explosion, fire, severe personal injury, or death.
SAFETY HOSE AND REGULATOR
Hold coupling nut and
regulator as shown for
proper connection to
LP cylinder valve.
Nipple has to be centered
into the LP cylinder valve.
1. Turn all grill control knobs to OFF.
2. Ensure that the regulator is tightly connected to LP cylinder.
3. Completely open LP cylinder valve by turning hand wheel counterclockwise. If you hear a rushing sound, turn gas off
immediately. There is a leak at the connection. Correct before proceeding.
4. Brush soapy solution onto hose and regulator and all connections from the LP tank to the main and side burner manifold.
5. If “growing” bubbles appear, there is a leak. Close LP cylinder valve immediately and re-tighten connections. If leaks
cannot be stopped do not try to repair. Call for replacement parts. Order new parts by providing the serial number, model
number, name and part number of items required (see parts list) to a Customer Care Agent 1-877-707-5463.
6. Always close LP cylinder valve after performing leak test by turning hand wheel clockwise.
ATTENTION
If it is evident there is excessive abrasion or wear, or the hose is cut, it must be replaced prior to the
outdoor cooking gas appliance being put into operation. The replacement hose assembly shall be that
specified by the manufacturer.
WARNING
For all new, at home, natural gas connections please contact a certified gas technician to install your
natural gas barbecue.
FOR NATURAL GAS MODELS (if applicable)
All Master Chef Natural Gas Barbecues come equipped with a 10’ or 12’ Natural Gas hose with a quick connect socket connection.
This will allow you to attach your Barbecue to your residential gas line.
To Connect
1. Push back the sleeve on the Quick Connect socket and insert plug and release the sleeve as shown.
2. Push the two pieces together until the sleeve snaps forward, to lock the plug in the socket.
To Disconnect
1. Push sleeve back and pull the plug out.
Testing For Gas Leaks
Before attempting to operate this Grill:
• Always confirm that all burner control knobs are in the OFF position.
• Always connect the gas supply hose first, open lid and then open the gas shutoff valve.
º Always use a brush or spray bottle to apply a 50/50 solution of liquid soap and water to all connection points, to test for
gas leaks. Never use a match or open flame for that purpose.
º Always look for bubbles to appear, as the appearance of bubbles will indicate a gas leak.
º Always turn off the gas immediately and tighten the connection, if you find that a leak has been detected.
º Before lighting the grill, always repeat this procedure until no further gas leaks are found.
º If a leak cannot be stopped, do not attempt to light the grill. Always contact a certified Natural Gas technician for assistance or
the Master Chef Customer Care Hotline for assistance. 1-888-707-5463.
LEAK TESTING THE VALVE, HOSE AND REGULATOR ASSEMBLY
Figure A