MTD 230EN - Manual (Page 15)

15
REF
NO.
PART No. DESCRIPTION Qty.
1 629-0236 Extension Cord 1
2 710-0627 Hex Screw, 5/16-24 x .75 1
6 710-1003 Screw, #10-16 x .625 2
4 710-3025 Hex Screw, 5/16-18 x .625 4
5 712-04063 Hex Flange Lock Nut, 5/16-18 2
6 725-0157 Push Mount Cable Tie 1
7 726-0154 Push Mount Cable Tie 1
8 726-0205 Clamp, Hose 2
9 736-0119 Washer, Lock 5/16 4
10 736-0159 Flat Washer .349 x .879 x .063 1
11 747-04150 Gas Tank Support Wire 1
12 7511825510 Choke Lever Knob 1
13 751-0535 Hose, Fuel Line 18
14 751-10023 Tank, Fuel 1
15 751-10278 Cap, Fuel 1
16 754-0101A V-Belt, 1/2 1
17 756-0416B Pulley Half, .625 ID x 2.25 OD 2
18 756-0475 Pulley, 1/2 V 1/2-20 LH x 6.0 1
19 790-00225 2-Cycle Mounting Bracket 1
20 734-04070 Wheel, 7 x 1.61 Dia. Tread 2
21 684-04027A Auger Assembly Complete 1
22 710-0106 Hex Screw, 1/4-20 x 1.00 Gr. 5 1
23 710-0642 Hex Screw 1/4-20 x .75 Gr. 5 1
24 710-0653 Self-tapping Screw 1/4-20 x .375 1
25 710-0896 Hex Screw, 1/4-14 x 0.625” 24
26 710-1005 Self-tapping Screw, 1/4-14 x .50” 6
27 710-3008 Hex Screw 5/16-18 x .75 1
9
Part List:
Snow
Thrower
REF
NO.
PART No. DESCRIPTION Qty.
28 712-04064 Hex Flange Lock Nut, 1/4-20 1
29 726-0299 Push Cap, 1/2” 2
30 732-0357A Extension Spring 1
31 736-0176 Flat Washer .265 x .938 x .120 4
32 736-0326 Flat Washer .510 x 1.0 x .125 1
33 736-0329 Lock Washer, 1/4 1
34 741-0600 Ball Bearing 17 x 40 x 12 2
35 684-04168 Idler Pulley (Pulley hole 1/4”) 1
36 748-0234 Shoulder Spacer .25 1
37 712-0896 Hex Lock Nut 1/4-28 1
38 784-5174 Bearing Cup 2
39 790-00238A Idler Brkt. w/Brake (Pulley hole 1/4”) 1
40 790-00045 Belt Cover 1
41 756-0625 Cable Roller 1
42 735-04033 Rubber Paddle 2
43 735-04032 Crescent Spiral 4
44 684-04025A Auger Axle 1
45 7510009636 Recoil Handle, Mitten (Optional) 1
46 7512B1476 Primer 1
47 738-0924 Carriage Screw 1/4-28 1
48 684-04167 Auger Assembly Housing 21” 1
49 790-00238 Idler Brkt. w/ Brake (Pulley hole 3/8”) 1
50 756-0313 Idler Pulley (3/8” hole) 1
51 710-0191 Hex Screw 3/8-24 x 1.25 1
52 712-0116 Jam Lock Nut 3/8--24 1
53 7519630 Recoil Handle (Optional) 1
54 722-3022 Foam Tape .625 X.25 2
NOTES: For a proper working machine,
use Factory Approved Parts. V-belts are
designed to engage and disengage safely.
A substitute (non OEM) V-belt can be
dangerous by not disengaging completely.
NOTE: Snow thrower features/components vary by model. NOT all parts listed above and pictured on the previous
page are standard equipment.
For parts and/or
accessories
please call
1-800-800-7310, or
1-330-220-4683.
www.mtdproducts.com