MTD 260 - Manual (Page 21)

21
Model 260 Series
REF.
NO. PART NO. DESCRIPTION
1 712-3025 Hex Jam Nut 5/16-24
2 736-0425 Bell Wash .325 x .930 x .045
3 756-1042 Pulley
4 736-0425 Bell Wash .325 x .930 x .045
5 712-0896 Hex Nut 1/4 - 28 Lock
6 736-0406 Flat Wash .442 x 1.38 x .060
7 782-7598 Belt Keeper
8 741-0124 Ball Bearing
9 721-0457 Oil Seal
10 750-1050 Flange Spacer
11 682-0028 Idler Bracket Ass’y
12 741-0682A Bearing Sleeve
13 732-0849A Wash:Flat:.504 x .700 x .030
14 710-0299 Hex Cap Screw 1/4-28 x 1.00 Gr. 5
15 736-0570 Flat Washer .865 x 1.145 x .030
16 741-0699 Needle Bearing .438 x .625 x .500
17 721-0325 Plug 1/4 x .437
18 618-0300 Housing Asm:Upper:(Incl. #16)
19 721-0329 Seal:Oil:.500x .687 x .094
20 741-0673 Flange Bearing .503 x .689 x .792
21 611-0105 Output Shaft
22 736-0520 Flat Washer .504 x .700 x .030
23 717-1492 Pinion Shaft 10T.
24 736-0314 Thrust Washer .375 x .70 x .030
25 736-0569 Thrust Washer .388 x .625 x .062
26 618-0299 Housing:Lwr: (Includes #27)
27 741-0672 Flange Bearing .378 x .531 x .370
28 710-1276 Hex Screw w/Wash 1/4-20 x .750
29 618-0298 Transmission-Complete (Incl. 1 thru 30)
30 732-0708 Bearing Retainer
31 741-0604 Bearing Sleeve .50 I.D.
32 748-0355 Bearing Support
33 736-0447 Wave Washer 1.5 x 1.0 x .029
34 782-0512B Height Adj. Plate: RH
35 782-0511A Height Adj. Plate: LH
36 682-0509 Pivot Plate Asm.
37 732-0706 Front Lever R.H
38 732-0707 Front Lever L.H.
39 720-0190 Knob
40 710-0216 Hex Cap Screw 3/8-16 x .75
41 736-0474 Washer DD 1.5" O.D.
42 716-0102 Snap Ring 1.0 Dia
43 782-7551 Wheel Dust Cap
44 717-1534 Gear 14T RH Fwd
45 717-1533 Gear 14T LH Fwd
46 634-0021A Whl 8x1.75 Disk Bar Gray Sleev S
47 720-0249 Hubcap:Euro:Grey
48 682-0512A Height Adj. Complete RH
49 682-0511A Height Adj. Complete LH
50 682-0030 Cable Idler Bracket
51 715-0221 Dowel Pin
52 736-3013 Flat Washer 1/2 x 1.00 x .063
53 714-0101 Cotter Pin .08 x 1.42
54 738-1002 Screw, Shoulder .375 x .25AB: 1/4-20
55 754-0466 “V”-Belt
REF.
NO. PART NO. DESCRIPTION