Philips Magnavox MWD2206A - Manual (Page 8)

Setup
– 8 – EN
1 Turn on the TV and set it to channel .
• If channel  has been already occupied for broadcasting,
see “RF Output Channel” section on page 6.
2 Select your language in the first time you turn on this unit.
Then press
[ B ] to go to next step.
3 Press [ B ] to start Auto Set Up.
or
STANDBY-ON
1 Press [MENU] to select “CHANNEL SET UP”.
Then press [B] to go to next step.
2 Select “MANUAL SET UP”.
Then press
[B] to go to next step.
3 Select the channel to be added or deleted.
4 Select “ADD” or “DELETE”.
5 To exit the menu
1 Press [MENU] and select “CLOCK SET”.
Then press [B] to go to next step.
2 Select the current month.
Then press
[B] to go to next step.
3 Select the current day.
Then press
[B] to go to next step.
4 Select the current year.
Then press
[B] to go to next step.
5 Select the current hour.
Then press
[B] to go to next step.
6 Select the current minute.
Then press
[B] to go to next step.
7 Select “AM” or “PM”.
8 To exit the CLOCK SET screen
To Preset the Channel Again
1) Press [MENU] until the main menu appears.
2) Select “CHANNEL SET UP” by using [K//L], then press [B].
) Select “AUTO SET UP” by using [K//L], then press [B]. After
scanning, the tuner stops on the lowest memorized channel.
To Change the On-Screen Language
1) Press [MENU] until the main menu appears.
2) Select “LANGUAGE SELECT” by using [K/L], then
press [B].
) Select “ENGLISH” , “FRANCAIS” or “ESPAÑOL” by
using [K/L] then press [CLEAR/C.RESET].
To Select a Channel
You can select a channel by using the Number buttons or
[ SKIP/CH. G/K, H/L ].
Notes for using the Number buttons:
• When selecting cable channels which are higher than 99,
enter channel numbers as a three-digit number. (for exam-
ple: 117, press [1], [1], [7])
• You must precede single-digit channel numbers with a zero.
(for example: 02, 0, 04 and so on)
• If the clock is not set, the CLOCK SET screen appears when you press
[MENU]. In this case, go to step 2.
To Add or Delete Channels
CLEAR/
C. RESET
Preparation for Use
Hint
• Repeat these steps only if either there was a power failure or this unit has been
unplugged for more than 0 seconds.
No Please wait for a few minutes. After scanning...
• The tuner stops on the lowest memorized channel.
• You can select only the channels memorized in this unit by using
[SKIP/CH. G///K, H//L] (or [CHANNEL K///L]).
• If “AUTO SET UP” appears on the TV screen again, check the cable
connections. Then, press [B] once again.
Yes
Press [MENU] to exit.
• Refer to “Hint for Cable Box or Satellite Box” section on page 6.
Do you connect the cable from the cable box or the satellite box to the unit’s
ANT-IN jack?
Hint
• To go back one step, press [s] (during steps 2 to 7).
• Your clock setting will be lost if either there is a power failure or this unit has
been unplugged for more than 0 seconds.
or
or
MENU
or
or
or
or
or
or
MENU
or
• If the clock is not set, the “CLOCK SET” screen appears when you press
[MENU]. In this case, press [MENU] again.
LANGUAGE SELECT
B ENGLISH [ON]
FRANCAIS
ESPAÑOL
CH 01
AUTO SET UP
- M E N U -
TIMER PROGRAMMING
AUTO REPEAT [OFF]
B CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
CHANNEL SET UP
AUTO SET UP
B MANUAL SET UP
MANUAL SET UP
CHANNEL 0 (CATV)
ADD
MANUAL SET UP
CHANNEL 0 (CATV)
DELETE
- M E N U -
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
CLOCK SET
MONTH DAY YEAR
1 0 / – – – – – –
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 – – – –
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 2 0 0 6
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 MON 2 0 0 6
HOUR MINUTE AM/PM
0 5 : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 MON 2 0 0 6
HOUR MINUTE AM/PM
0 5 : 4 0 – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 MON 2 0 0 6
HOUR MINUTE AM/PM
0 5 : 4 0 P M AM
B PM
or
or
NO YES
Turn On the Unit for the First Time
VCR
Clock Setup
VCR
Operation described in this manual are
mainly based on the remote control.
Hint
• If you accidentally select Spanish or French and need English: Press [MENU]
and choose SELEC. IDIOMA or SELECTION LANGUE. Press [B] and select
ENGLISH. Finally, press [CLEAR/C.RESET].
VCR
MWD2206A_H986NUD.indd 8 2006/01/18 18:9:28