MACKIE Compact Mixer - Manual

17
Compact Mixer Reference Guide
MIXER ANATOMY: CHAPTER 2
Inputs, Outputs, and Related Controls
Mackie E-Z Interfacing
Concerned about levels, balancing, impedance,
polarity, or other interface goblins? Don’t be. On
your Mackie mixer, you can connect almost anything
almost anywhere, with nary a care. Here’s why:
• Every main input and output is balanced .
• Every 1/4" input and output jack also accepts
unbalanced connections.
• Every input is designed to accept virtually any
output impedance.
• The main left and right mix outputs can de-
liver +28 dBu into a 600 ohm load (that’s hot!)
• All the other outputs can deliver +22 dBu into
a 600 ohm load (that’s plenty).
• All the outputs are in phase with the inputs.
All Mackie mixers have both microphone and line-
level inputs. Some channels have both, some chan-
nels have only line-level inputs. Consult your mixer’s
quick start guide (or just look at the connector
panel) for the exact arrangement. Below is the rear
panel of the 1604-VLZ PRO.
Mic? Line? – What’s The Difference?
Microphones produce a relatively low
voltage, generally in the range of 1 to 250
millivolts, depending on the sensitivity of
the mic, and how loud the sound is. Voltages in the
0.15 to 3 volt range are considered to be line-level.
These aren’t rules or standards, just ways of talking
about two widely different operating voltage ranges,
both of which are common in audio.
A microphone typically requires 20 to 60 dB of gain
in order to bring its signal up to the mixer’s operat-
ing level. A line-level signal requires little if any gain,
and may need to be brought down in level to match
the mixer. So, while there’s a wide adjustment range
for both mic and line inputs, the mic inputs have
higher gain.
Don’t forget the Level-Setting Proce-
dure at the beginning of this book. Mic
and line inputs are happiest when run-
ning at the optimum levels. That procedure will get
you there.
Check the Tips section and Glossary for more infor-
mation about terms we’ll be using here like operating
level, impedance, balanced, unbalanced, XLR, and
TRS. Also study the mixer block diagrams, as each
one is worth a thousand words or more.
Mic Inputs
Mackie mixers include phantom-powered, bal-
anced XLR microphone inputs just like the big studio
mega-consoles, and for exactly the same reason:
A fully balanced circuit is excellent at rejecting
hum and noise, and phantom powering means that
condenser mics can be used without external power
supplies or batteries.
You can plug in almost any kind of mic that has a
standard male XLR-type connector without fear of
overloading the preamp. Professional ribbon, dy-
namic, and condenser mics all sound great through
these inputs.
XLR Input Connectors – Mic wiring
Nearly all professional mics are designed to con-
nect to a low impedance input, and employ balanced
wiring terminating in an XLR-style plug. You’ll fi nd an
illustration and wiring diagram in the Tips section,
chapter 9. We use the wiring convention:
Pin 1 = shield
Pin 2 = positive (+ or hot)
Pin 3 = negative (- or cold)
UTILISE UN FUSIBLE DE RECHANGE DE MÊME TYPE. DEBRANCHER AVANT DE REMPLACER LE FUSIBLE
4 3 2 1
INSERT INSERT INSERT
LINE
INSERT
MIC 4 MIC 3 MIC 2 MIC 1
BAL
UN-
BAL BAL
UN-
BAL BAL
UN-
BAL BAL
UN-
BAL
LINE LINE LINE
O O +6
PHANTOM ON POWER ON 120 VAC 50/60 Hz 20W 1A/250V SLO-BLO
16 15 14 13 12 11 10 9 8 7 6 5
MIC 16
INSERT INSERT INSERT INSERT INSERT INSERT INSERT INSERT INSERT INSERT INSERT INSERT
MIC 15 MIC 14 MIC 13 MIC 12 MIC 11 MIC 10 MIC 9 MIC 8 MIC 7 MIC 6 MIC 5
SUB OUT C-R OUT MAIN INSERT (TIP SEND RING RETURN)
TAPE TAPE MAIN OUT AUX SEND DIRECT OUT AUX RETURN
3
R
L
MONO
R R R R
L
R
L
R
L
R
L
L L L
1
4 2
5 1 2 3 4 3 1
6 4 2
7 5 3
8 6 4
1
2
BAL/UNBAL BAL/UNBAL BAL/UNBAL BAL/UNBAL BAL/UNBAL BAL/UNBAL INPUT OUTPUT
R
L
(MONO) (MONO) (MONO)
BAL
UN-
BAL BAL
UN-
BAL BAL
UN-
BAL BAL
UN-
BAL BAL
UN-
BAL BAL
UN-
BAL BAL
UN-
BAL BAL
UN-
BAL BAL
UN-
BAL BAL
UN-
BAL BAL
UN-
BAL BAL
UN-
BAL
LINE LINE LINE LINE LINE LINE LINE LINE LINE LINE LINE LINE
TO REDUCE THE RISK OF FIRE REPLACE WITH SAME TYPE FUSE AND RATING
CAUTION:
UTILISE UN FUSIBLE DE RECHANGE DE MÊME TYPE. DEBRANCHER AVANT DE REMPLACER LE FUSIBLE
CONCEIVED, DESIGNED, AND MANUFACTURED BY MACKIE DESIGNS INC • WOODINVILLE • WA • USA • MADE IN USA • FABRIQUE AU USA • COPYRIGHT ©1998 • THE FOLLOWING ARE TRADEMARKS OR REGISTERED TRADEMARKS OF MACKIE DESIGN INC.: "MACKIE", "VLZ", "XDR", AND THE "RUNNING MAN" FIGURE • US PATENT NUMBER 29/049,129
XDR TM EXTENDED DYNAMIC RANGE MIC PREAMPLIFIERS ARE PROPRIETARY TO MACKIE DESIGNS, INC.
XDR MIC PRE XDR MIC PRE XDR MIC PRE XDR MIC PRE XDR MIC PRE XDR MIC PRE XDR MIC PRE XDR MIC PRE XDR MIC PRE XDR MIC PRE XDR MIC PRE XDR MIC PRE XDR MIC PRE XDR MIC PRE XDR MIC PRE XDR MIC PRE