MACKIE 1800SA - Manual (Page 5)

5
REAR PANEL DESCRIPTION
POWER Switch
Switch up to turn the FUSSION 1800SA
on, and switch down to turn it off. Make
sure the signal source’s level control is
turned down before you turn it on.
POWER Indicator
When the POWER switch is turned on,
and the linecord is connected to an active
AC Mains supply, this indicator lights green
to let you know that you’re ready to rock
and roll.
MAIN INPUT
This is a female XLR-type connector that
accepts a balanced line-level SUB OUT signal
from a Fussion Series full-range active
speaker system.
LOOP OUT
This is a male XLR-type connector that
produces exactly the same signal that is
connected to the
MAIN INPUT jack. Use it to
daisy-chain several FUSSION 1800SAs to-
gether off the same signal source.
POWER OUT
This is a female Neutrik™ Speakon con-
nector that produces a speaker-level signal
between the frequencies of 35Hz to 85Hz.
Connect this to the FUSSION 1800S pas-
sive subwoofer. The signal at this connector
comes from a 2000W amplifier identical to
the one powering the FUSSION 1800SA.
AC Receptacle
This is where you connect the AC line-
cord to provide AC power to the FUSSION
1800SA’s built-in power amplifiers. Plug
the linecord into an AC socket properly
configured for your particular model.
The FUSSION 1800SA is shipped with a
connector that mates with the AC recep-
tacle on the rear panel. Use heavy gauge
wire for the linecord to avoid power losses
across the wire. (See page 8 for more info.)
The bar A on the rear panel is there to
secure the linecord and prevent it from acci-
dentally getting pulled loose from the AC
receptacle. Wrap the linecord through the
bar and tie it in a knot to secure it.
Note: You can change the AC voltage
configuration from 115V to 230V (or vice
versa) internally by reconfiguring the trans-
former primary wiring on the power supply
board. Contact Mackie Technical Support
for instructions (1-800-258-6883).
FUSE
Always replace the fuse with the type in-
dicated on the rear panel. Never replace the
fuse with one of a higher value than indi-
cated on the rear panel.
WARNING: Make sure
you use the correct fuse
relative to the AC operat-
ing voltage.
115VAC=16A Slow-Blow
230VAC=10A Slow-Blow
FUSE
NEMA LS-20 20A-115VAC
FUSE
16A / SB
OFF
ON
POWER
CONCEIVED, DESIGNED, AND MANUFACTURED BY MACKIE DESIGNS INC, WOODINVILLE, WA, USA
AND MACKIE EUROPE • MANUFACTURED IN ITALY • COPYRIGHT ©1998 •
THE FOLLOWING ARE TRADEMARKS OR REGISTERED TRADEMARKS OF MACKIE DESIGNS INC.:
"MACKIE", AND THE "RUNNING MAN" FIGURE • PATENT PENDING
LOOP OUT
POWER OUT
35-85Hz
MAIN INPUT
PARALLEL
MIN. 8
WARNING: THIS SURFACE MAY REACH HIGH TEMPERATURE DURING
STANDARD USE. TO ENSURE PROPER OPERATION ALLOW A MINIMUM OF 6 INS.
OF CLEARANCE FROM THIS SURFACE AND ADEQUATE VENTILATION. TO REDUCE
THE RISK OF ELECTRIC SHOCK DO NOT REMOVE THIS PANEL OR ANY ATTACHED
COMPONENT. NO OPERATOR SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED PERSONNEL. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
REPLACE WITH THE SAME TYPE FUSE AND RATING.
DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE UTILISE UN FUSIBLE DE RECHANGE DE MÊME TYPE.
DEBRANCHER AVANT DE REMPLACER LE FUSIBLE
CAUTION
AVIS: RISQUE DE CHOC ELECTRIQUE — NE PAS OUVRIR
SERIAL NUMBER MANUFACTURING DATE
1800SA FUSSION
FS ™
115VAC Version
FUSE FUSE
10A / SB
POWER
10A - 230 VAC
230VAC Version
A