MACKIE ONYX 1220I - Manual (Page 22)

22 Onyx 1220i
Tape is the stereo signal coming in from the tape in
[15] RCA jacks. FireWire is a 2-track feed coming in
through the FireWire [3] connection from your
computer. Alt 3-4 is the additional stereo mix bus
formed when any channel is muted with the
mute/alt 3-4 switch [31].
Selections made here deliver stereo signals to the
control room, phones, and meters. With no switches or
main mix [35] engaged, there will be no signal at these
outputs and no meter indication.
The exception is the solo function. Regardless of the
source matrix selection here, engaging a channel’s solo
switch will replace that selection with the solo signal,
sent to the control room, phones, and the right meter.
37. ASSIGN TO MAIN MIX
Let’s say you’re doing a live show: "You're doing a live
show." Intermission is nearing and you want to play a
soothing CD for the crowd to prevent them from
becoming antsy. Simply engage this switch and your
source matrix selection, after going through the control
room level control, will feed into the main mix, just as if
it were another stereo channel.
What if you have a playlist of MP3 fi les on your
computer you want to play during the break? Engage
this switch and the FireWire switch [36] to play your
MP3s directly from your computer, through the source
matrix, and into the main mix.
Another handy use for this switch is to enable the
alt 3-4 mix to become a submix of the main mix, using
the control room level control.
Side effects to engaging this switch:
1. It will also feed any soloed channels into the
main mix, which may be the last thing you
want.
2. If you have main mix as your source matrix
selection and then engage this switch, the main
mix lines to the source matrix will be
disconnected from the control room and phones
outputs, to prevent feedback.
3. If you have tape as your source matrix
selection, and then engage this switch, it can
create a feedback path between tape in and
tape out. Make sure your tape deck is not in
record, record-pause, or input monitor mode
when you engage these switches, or make sure
the control room knob [38] is turned all the
way down.
38. CONTROL ROOM Knob
This controls the volume at the control room outputs,
from off to maximum gain (+10 dB). It also controls the
level of the control room signal going to the main outs
when assign to main mix [37] is selected.
CTRL ROOM/PHONES
SOURCE
PHONES CONTROL
ROOM
RUDE
SOLO
20
15
10
6
3
0
2
4
7
10
20
30
L R
0dB=0dBu
LEVEL
SET
CLIP
MAIN MIX
ALT 3-4
TAPE
FW 1-2
ASSIGN TO
MAIN MIX
MAX O O MAX O O
Control Room/Phones and
Meters
Typically, the engineer sends the main mix to an
audience (for a live show) or to a mixdown deck (if
recording). But what if the engineer needs to hear
something other than the main mix in the control room
or headphones? With the Onyx 1220i, the engineer has
several choices of what to listen to. This is one of those
tricky parts, so buckle up.
35. MAIN MIX
Press this switch in to listen to the main mix in your
control room and headphones, and to check the main
mix levels in the meters. In addition to the main mix,
you can listen to any combination of tape, FW 1-2 and
alt 3-4, depending on which of these switches [36] is
engaged.
If the assign to main mix switch [37] is
engaged, you cannot hear the main mix in the
control room or headphones, or see its level
on the meters. This is to prevent feedback caused by
sending the main mix to the main mix.
36. TAPE, FW 1-2, ALT 3-4
Using these source switches, you can choose to listen
to any combination of tape, FireWire, and alt 3-4 in the
control room and headphones, in addition to the main
mix if its source switch [35] is engaged.
35
36
37
38
40
39 41