Port vlan filter, Enter a vlan id in the management vlan ids field – IMC Networks iMcV-Giga-FiberLinX-II User Manual
Page 44
40
Port VLAN Filter
The VLAN filter mode allows you to isolate a segment of the network to only accept
data using some or all of the 32 available VLAN IDs.
To configure this mode, do the following:
1. In the Main Configuration screen, press the space bar and type config. The
Configuration screen displays:
2. Enter N in the Transparent Mode field and press any key (except S or Q) to open
the VLAN screen:
3. Enter Y in the Tags column of both the Optics row and the Data row to enable
Data VLANs.
VLAN IDs Priorities Tags
Current Saved Current Saved
Ports Data VLANs are used only
Optics [0 ] [
0
] [0 ] [
0
] [
Y
] if Tags are enabled on both
Data [0 ] [
0
] [0 ] [
0
] [
Y
] the Optics and Data Ports.
Saved VLAN Values <Active after reboot>. Current VLAN Values <Active now>.
Tags
VLAN IDs Priorities
Current Saved Current Saved
Ports Data VLANs are used only
Optics [0 ] [
0
] [0 ] [
0
] [
N
] if Tags are enabled on both
e Optics and Data Ports.
Data [0 ] [
0
] [0 ] [
0
] [
N
] th
Management VLAN EXT Mgmt Tag
NMP [20 ] [
0
] [0 ] [
0
] [
N
]
S
Data VLANs <Optics <----> Data>
VLAN 1 [0 ] [
0
] VLAN 12 [0 ] [
0
] VLAN 23 [0 ] [
0
]
VLAN 2 [0 ] [
0
] VLAN 13 [0 ] [
0
] VLAN 24 [0 ] [
0
]
VLAN 3 [0 ] [
0
] VLAN 14 [0 ] [
0
] VLAN 25 [0 ] [
0
]
VLAN 4 [0 ] [
0
] VLAN 15 [0 ] [
0
] VLAN 26 [0 ] [
0
]
VLAN 5 [0 ] [
0
] VLAN 16 [0 ] [
0
] VLAN 27 [0 ] [
0
]
VLAN 6 [0 ] [
0
] VLAN 17 [0 ] [
0
] VLAN 28 [0 ] [
0
]
VLAN 7 [0 ] [
0
] VLAN 18 [0 ] [
0
] VLAN 29 [0 ] [
0
]
VLAN 8 [0 ] [
0
] VLAN 19 [0 ] [
0
] VLAN 30 [0 ] [
0
]
VLAN 9 [0 ] [
0
] VLAN 20 [0 ] [
0
] VLAN 31 [0 ] [
0
]
VLAN 32 [0 ] [
0
]
VLAN 10 [0 ] [
0
] VLAN 21 [0 ] [
0
]
VLAN 11 [0 ] [
0
] VLAN 22 [0 ] [
0
]
7.
Valid VLAN IDs are between 1 and 4094. Valid priorities are between 0 and
Type S or F3 to save the changes. Type Q or F4 to quit and cancel changes.
Transparent Mode – with either (not both) Data and Optics Mgmt dipswitches
set to on, all traffic passes between Optics and Data port EXCEPT what has
been defined as the Management Domain. The Management Domain can either be
efined as untagged traffic or traffic with a specified VLAN ID.
d
In Transparent Mode with BOTH Optics and Data Mgmt dipswitches set to off,
ll traffic passes between the Optics and Data Ports.
a
efault Mode – the unit passes only Untagged Packets.
D
he unit is currently
in Default Mode
.
T
Enter Y for Transparent Mode, N for no Transparent Mode or <enter> to
move to other options [ N ]
4. Enter a VLAN ID in the Management VLAN IDs field.