IBM 8xx - Manual (Page 77)

Asm–
Index Part
Number
Units Description
25– See “How to Use This Parts Manual” on page v for general parts manual
information, including ordering parts. See “Identifying a Right Hand or Left Hand
Model” on page v for how to identify left hand and right hand models.
– 41J7434 1 Transport conveyor assembly, 19 in., 115V
– 44M1899 1 Transport conveyor assembly with Sensormatic, 19 in., 115V, right hand
– 44M1900 1 Transport conveyor assembly with Sensormatic, 19 in., 115V, left hand
– 41J7438 1 Transport conveyor assembly, 19 in., 230V
– 41J7442 1 Transport conveyor assembly, 25 in., 115V
– 44D0405 1 Transport conveyor assembly with Sensormatic, 25 in., 115V, right hand
– 44D0407 1 Transport conveyor assembly with Sensormatic, 25 in., 115V, left hand
– 41J7446 1 Transport conveyor assembly, 25 in., 230V
–1 28R3196 1 Guide, tracking, motor end (order with 28R3195). Adhesive plastic sticker.
–2 28R3189 1 Belt, transport conveyor (for standard lane with 19 inch belt)
–2 28R3274 1 Belt, transport conveyor (for wide lane with 25 inch belt)
–3 41D9769 1 LED light visor mount (not shown, located on motor cable)
–4 41J9310 1 Motorized pulley, 19" conveyor 115-60hz, unbalanced (transport only)
–4 41D9818 1 Motorized pulley, 19" transport conveyor 230V
–4 41J9318 1 Motorized pulley, 25" conveyor 115-60hz, unbalanced (transport only)
–4 41D9820 1 Motorized pulley, 25" transport conveyor 230V
–5 41J8438 1 Crossbar, conveyor frame (for standard lane with 19 inch belt)
–5 28R3279 1 Crossbar, conveyor frame (for wide lane with 25 inch belt)
–6 28R3298 1 Roller (for standard lane with 19 inch belt)
–6 28R3275 1 Roller (for wide lane with 25 inch belt)
–7 28R3197 1 Guide, tracking, motor end (order with 28R3194). Adhesive plastic sticker.
–8 41J7666 2 Bracket, drive isolation. Large black coupling. Use to adjust and isolate motor. (one
on each side)
–9 28R3285 2 Drive roller retaining angle (one on each side)
–10 28R3283 2 Block, idler roller (one on each side)
–11 28R3284 2 Bracket, tensioner (one on each side)
–12 28R3172 1 Nosebar adjusting angle
–13 41J7426 1 Plate, side, transport conveyor, left side
–14 41J6928 1 Emitter/detector bracket, bagging area full sensor
–15 41D7146 1 Emitter, bagging area full sensor (for standard lane with 19 inch belt)
–15 41J8450 1 Emitter, bagging area full sensor (for wide lane with 25 inch belt)
–16 28R3195 1 Guide, tracking, motor end (order with 28R3196). Adhesive plastic sticker.
–17 41J7448 1 Assembly, nosebar, (for standard lane with 19 inch belt) (Replaces 28R7098)
–17 41J7450 1 Assembly, nosebar, (for wide lane with 25 inch belt) (Replaces 28R7084)
–18 41J8332 1 Skid plate, (for standard lane with 19 inch belt), no Sensormatic
–18 44M1913 1 Skid plate with Sensormatic opening, (for standard lane with 19 inch belt), right
hand
–18 44M1914 1 Skid plate with Sensormatic opening, (for standard lane with 19 inch belt), left hand
–18 41J8334 1 Skid plate, (for wide lane with 25 inch belt), no Sensormatic
–19 28R3194 1 Guide, tracking, motor end (order with 28R3197). Adhesive plastic sticker.
–20 41J7425 1 Plate, side, transport conveyor, right side plate
–21 41D7150 1 Detector, bagging area full sensor (for standard lane with 19 inch belt)
–21 41J8452 1 Detector, bagging area full sensor (for wide lane with 25 inch belt)
– 41J7126 1 25 inch order separator (not shown). See 42–1 on page 121.
– 41J7127 1 19 inch order separator (not shown). See 42–1 on page 121.
– 41J8854 1 Sensor cable, transition plate (not shown)
– 41J8855 1 Transition plate emitter (not shown)
– 41J8856 1 Transition plate detector (not shown)
– 42H1161 1 Cable tie (not shown)
– 41J8336 1 Wire cord clips (bag of 10)
Assembly 25: (continued)
Updated October 16, 2007
Chapter 4. Transport Conveyor 65