Ingersoll-Rand S120-EU - Manual (Page 2)

2
WARNING LABEL IDENTIFICATION
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
Always wear eye protection
when operating or perform-
ing maintenance on this
tool.
WARNING WARNING
Always wear hearing
protection when operating
this tool.
Always turn off the air sup-
ply and disconnect the air
supply hose before install-
ing, removing or adjusting
any accessory on this tool,
or before performing any
maintenance on this tool.
WARNING
Air powered tools can vibrate
in use. Vibration, repetitive
motions or uncomfortable po-
sitions may be harmful to your
hands and arms. Stop using
any tool if discomfort, tingling
feeling or pain occurs. Seek
medical advice before resum-
ing use.
WARNING
Do not carry the tool by
the hose.
WARNING WARNING
Do not use damaged, frayed
or deteriorated air hoses
and fittings.
WARNING
Keep body stance balanced
and firm. Do not overreach
when operating this tool.
WARNING
Operate at 90 psig (6.2 bar/
620 kPa) Maximum air pressure.
90 psig
(6.2bar/620 kPa)
International Warning Label:
Order Part No. ___________
USING THE TOOL (Continued from page 1)
•
Make sure that sparks, if emitted, are directed so as
not to cause a hazard.
•
Keep work area clean. Cluttered areas and benches
invite injuries.
•
Keep work area well lit.
•
Keep children away. Do not let visitors touch the tool.
•
Store idle tools. When not in use, tools should be
stored in a dry, high or locked place, out of reach of
children.
•
Use the right tool. Do not force small tools or
attachments to do the job of a heavy duty tool.
Do not use tools for purposes not intended.
•
Secure work. Use clamps or a vise to hold the work.
•
Remove adjusting keys and wrenches before using.
•
Stay alert. Watch what you are doing. Use common
sense. Do not operate tool when you are tired.
SAW SPECIFIC WARNINGS
•
Do not use a Saw without the proper guards.
•
Do not use a blade for which the recommended speed
is lower than the actual free speed of the Saw.
•
Moveable guards must not be locked in the open
position. Ensure that moveable guards operate freely
without jamming and that the retraction mechanism
operates freely.
•
Do not use a blade larger than 12” outside diameter
with a Model S120 Saw.
•
Before mounting a blade, after all tool repairs and
whenever a Saw is issued for use, check the free speed
of the Saw with a tachometer to make certain its
actual speed at 90 psig (6.2 bar/620 kPa) does not
exceed the rated free speed stamped on the nameplate
by more than 500 rpm.
•
Inspect all blades for chips or cracks prior to
mounting. Do not use a blade that is chipped or
cracked or otherwise damaged.
•
Before mounting or removing a blade, disconnect the
Saw from the air supply line, or shut off the air supply
and drain the hose.
•
Make certain the blade properly fits the arbor. The
blade should not fit too snugly or too loosely. Do not
use reducing bushings to adapt a blade to any arbor
unless such bushings are supplied by and
recommended by the blade manufacturer.
•
Always wear protective eyewear or a face shield when
operating a Saw. Also, use a face mask or dust mask if
the cutting operation produces an excessive amount of
dust. Use local exhaust venting if needed.
•
Always replace a damaged, bent or severely worn
guard.
•
Always use clean, sharp blades. A dull blade and/or a
blade with a buildup of gum and hardened pitch will
not cut efficiently. Clean the blade with either mineral
spirits or warm soap and water and dry thoroughly.
•
Use the proper style blade for the application.
•
Do not carry a Saw with the motor running.