INSTEON SWITCHLINC 2476S - Manual (Page 2)

SwitchLinc V2 Relay (#2476S)
Quick-Start Guide
SWITCHLINC RELAY
N Ne ee ed d H He ellp p? ? F Fo orr a as ss siis stta an nc ce e c ca allll yyo ou urr ffrriie en nd dllyy
s su up pp po orrtt p pe errs so on n @ @ 8 86 66 6--2 24 43 3--8 80 01 18 8
Quick-Start Guide
SWITCHLINC
Setting Up Your SwitchLinc Relay to Control an INSTEON Device Remotely
S Stte ep p 3 3.. Test that SwitchLinc Relay is working properly by turning the load on and off.
D De ev viic ce e S Se ettu up p IIn ns sttrru uc cttiio on ns s
SwitchLinc Dimmer • •P Prre es ss s a an nd d h ho olld d the SwitchLinc Dimmer’s Paddle Top for 10 seconds until the light it
controls flashes — then release.
The SwitchLinc Relay will exit Linking Mode, and its LED will stop blinking.
Lamp Dimmer • •P Prre es ss s a an nd d h ho olld d the Lamp Dimmer’s SET button for 3 seconds until the lamp it con-
trols flashes — then release.
The SwitchLinc Relay will exit Linking Mode, and its LED will stop blinking.
Appliance Module • •P Prre es ss s a an nd d h ho olld d the Appliance Module’s SET button for 3 seconds until its Status LED
blinks — then release.
The SwitchLinc Relay will exit Linking Mode, and its LED will stop blinking.
Other INSTEON-
Enabled Devices
See device’s Quick-Start Guide or User’s Guide
S Stte ep p 1 1..
P Prre es ss s a an nd d h ho olld d the SwitchLinc Relay’s Paddle Top for 10 seconds until its LED starts blinking -- then release.
Your SwitchLinc Relay is now in Linking Mode. You have 4 minutes to complete Step 2.
S Stte ep p 2 2..
Select the device you would like to control and follow the setup instructions from the table below:
•T Ta ap p the Paddle Top to turn your load on.
•T Ta ap p the Paddle Bottom to turn your load off.
Using Your SwitchLinc Relay
S Stte ep p 1 1..
On your INSTEON controller p prre es ss s a an nd d h ho olld d the ON button of your choice for 10 seconds until the LED begins
blinking slowly -- then release.
Your INSTEON Controller is now in Linking Mode. You have 4 minutes to complete step 2.
S Stte ep p 2 2.. P Prre es ss s a an nd d h ho olld d the SwitchLinc’s Paddle Top for 10 seconds until the LED flashes -- then release.
Your INSTEON Controller’s LED will stop blinking to indicate successful linking.
S Stte ep p 3 3..
On your INSTEON Controller press the ON and OFF buttons several times to make sure everything is working properly.
Setting Up an INSTEON Controller to Control a SwitchLinc Remotely
SwitchLinc V2 Relay (#2476S)
Quick-Start Guide
SWITCHLINC RELAY
N Ne ee ed d H He ellp p? ? F Fo orr a as ss siis stta an nc ce e c ca allll yyo ou urr ffrriie en nd dllyy
s su up pp po orrtt p pe errs so on n @ @ 8 86 66 6--2 24 43 3--8 80 01 18 8
T To o u un nlliin nk k a a d de ev viic ce e ffrro om m yyo ou urr S Sw wiittc ch hL Liin nc c R Re ella ayy
1. Press and hold the P Pa ad dd dlle e T To op p for 10 seconds -- then release.
2. Press and hold the P Pa ad dd dlle e T To op p a ag ga aiin n for 10 seconds -- then release.
3. On the INSTEON device you wish to unlink, press and hold the O ON N B Bu utttto on n for 10 seconds or the S SE ET T B Bu utttto on n for 3 seconds.
T To o ffa ac ctto orryy rre es se ett yyo ou urr S Sw wiittc ch hL Liin nc c R Re ella ayy
1. Press and hold the P Pa ad dd dlle e T To op p for 10 seconds -- then release.
2. Tap the S SE ET T B Bu utttto on n a allll tth he e w wa ayy iin n -- then release.
3. Push the S SE ET T B Bu utttto on n a allll tth he e w wa ayy iin n and hold for 10 seconds -- then release.
N No otte es s
• Pressing the SET Button after going into Linking Mode will change Linking Mode to Scene Setup (Multi-Link) Mode
• Any paddle press will exit Linking Mode early.
For detailed instructions on how to operate all the features of your SwitchLinc Relay,
please refer to the User's Guide at http://www.smarthome.com/2476s.html
Using Your SwitchLinc Relay’s Advanced Features
Optional for X10 Users
To give your SwitchLinc Relay an X10 Primary Address
1. Press and hold the P Pa ad dd dlle e T To op p for 10 seconds -- then release.
2. S Se en nd d tth he e d de es siirre ed d X X1 10 0 P Prriim ma arryy A Ad dd drre es ss s T TH HR RE EE E ttiim me es s..
To remove an X10 Primary Address from Your SwitchLinc Relay
1. Press and hold the P Pa ad dd dlle e T To op p for 10 seconds -- then release.
2. Press and hold the P Pa ad dd dlle e T To op p a ag ga aiin n for 10 seconds -- then release.
3. S Se en nd d a an nyy X X1 10 0 a ad dd drre es ss s T TH HR RE EE E ttiim me es s..