Invacare KSS - Manual (Page 11)

11
7. Torque socket screw to 75 - inch pounds.
8. Once twist release mounting clamps are secured,
do one (1) of following:
A. Refer to FIXED RELEASE CLAMPS FOR
BACK in PROCEDURE 2 of this instruction
sheet.
B. Refer to USING CLAMPS in this instruction
sheet.
Fixed Release Clamps For Back (FIGURE 13)
NOTE: Refer to INSTALLATION WARNING in the
SAFETY SUMMARY before proceeding.
NOTE: The fixed release rail/cane clamps are designed
to fit either 1-inch rail tubing or, with insert provided, 7/8-
inch rail tubing.
1. Remove the mounting screw, lock washer, and
internal threaded mounting screw from the fixed
release clamps (DETAIL “B”).
2. Place the fixed release clamp on the back cane.
3. If fixed release clamp is not tightly fitted around back
cane tubing, install insert provided as shown in DE-
TAIL “A”.
4. Install the fixed release clamp onto the back rail so
that the fixed portion is flush against and rests on top
of the mounting hook and is located between the
seat rail and the bottom of the mounting hook.
5. Reinstall the mounting screw, lock washer, and
internal mounting screw into the fixed release rail/
cane clamp and torque to 75 - inch pounds.
6. Repeat STEPS 1 - 5 for other side.
7. Once fixed release mounting clamps are secured,
do one (1) of following:
A. Refer to QUICK RELEASE CLAMPS FOR
SEAT in PROCEDURE 2 of this instruction sheet.
B. Refer to USING CLAMPS in this instruction sheet.
FIGURE 13- FIXED RELEASE CLAMPS FOR B FIGURE 13- FIXED RELEASE CLAMPS FOR B FIGURE 13- FIXED RELEASE CLAMPS FOR B FIGURE 13- FIXED RELEASE CLAMPS FOR B FIGURE 13- FIXED RELEASE CLAMPS FOR BA A A A AC K C K C K C K C K
DET DET DET DET DETAIL AIL AIL AIL AIL “B” “B” “B” “B” “B”
Lock
Washer
Sleeve
Mounting
Hook
Internal Mounting
Screw
Twist Release
Clamp
Fixed Release
Clamp
Mounting
Hooks
Seat Rail
Back Cane
Fixed
Portion
Inside of Back Cane
Quick Release Clamps For Seat
(FIGURE 14)
NOTE: Refer to INSTALLATION WARNING in the
SAFETY SUMMARY before proceeding.
NOTE: The quick release and fixed release clamps are
designed to fit either 1-inch rail tubing or, with insert pro-
vided, 7/8-inch rail tubing.
1. Remove the sleeve, lock washer, and internal threaded
mounting screw from the quick release clamp (DE-
TAIL “C”).
2. Place the quick release clamp on the seat rail.
3. If quick release clamp is not tightly fitted around seat
rail tubing, install insert provided as shown in DE-
TAIL “C”.
4. Install the quick release clamp onto the seat rail so
that the fixed portion is flush against and rests on top
of the mounting hook and the release portion is be-
tween the front riggings and the mounting hook.
5. Reinstall the sleeve, lock washer, and internal mount-
ing screw into the quick release clamp and torque to
75 - inch pounds.
6. Repeat STEPS 1- 5 for other side.
7. Once quick release mounting clamps are secured,
do one (1) of following:
A. Refer to FIXED RELEASE CLAMPS FOR
SEAT in PROCEDURE 2 of this instruction
sheet.
B. Refer to USING CLAMPS in this instruction
sheet.
FIGURE 13- FIXED RELEASE CLAMPS FOR B FIGURE 13- FIXED RELEASE CLAMPS FOR B FIGURE 13- FIXED RELEASE CLAMPS FOR B FIGURE 13- FIXED RELEASE CLAMPS FOR B FIGURE 13- FIXED RELEASE CLAMPS FOR BA A A A AC K C K C K C K C K