i. Tech Dynamic Arrow Lite - Manual (Page 2)

charger plug from the headset. Press and hold the MFB (refer to Figure 1) for two seconds to turn on
the headset. Please refer to “Turning Your Headset On and Off” for further details.
Talk and Standby Time
A fully charged battery can offer up to 7 hours of talk time and up to 120 hours of standby time. When
there are no calls the headset should remain turned on in standby mode.
Battery Low Indication
When the battery has become low when the headset is on, the status indicator will flash red and the
headset will emit a beep* every minute. Please follow the instructions described above to recharge
the battery.
*If you are pairing your headset and your mobile phone in a noisy environment, we advise you to put
on the earphone first so that the beep will be more audible.
Turning Your Headset On and Off
Turning On the Headset
Press and hold the MFB (see Figure 1) for two seconds until you hear a short beep. The status indicator
will then flash green.
IMPORTANT: Press the MFB again when you want to turn on the headset to re-activate pairing and
ensure the connection between the headset and the mobile phone is resumed. For pairing, please
refer to “Pairing Your Headset” on page 8 of this user guide.
Turning Off the Headset
Press and hold the MFB for two seconds until you hear a long beep. The status indicator will turn red
and the headset will turn off.
IMPORTANT: To disconnect the Bluetooth connection, press the headset’s MFB firmly to turn it off. If
you will not be using the headset for a while, we advise you turn off the Bluetooth function on your
mobile phone as well.
The headset works with Bluetooth-enabled mobile phones only. Prior to using and pairing
your headset for the first time, please check if your mobile phone is Bluetooth-enabled. This
information will normally feature on the packaging or user guide that is provided with your
mobile phone.
The pairing instructions for a typical Bluetooth-enabled mobile phone are explained on the
next page. The headset pairing procedure may vary depending on the model of your mobile
phone. Please contact the manufacturer of your mobile phone or its agent for further
information.
1. Place the headset and the mobile phone where they are no more than one metre apart.
2. Ensure the headset is off. (The status indicator is unlit and does not flash.)
Pairing Your Headset
Up to 1 meter
(Fig. 4)
Using Your Arrow Lite-R Headset
Answering a Call
When there is an incoming call, you will hear the ring through the earphone. Press the
MFB once to accept the call or answer the call via your mobile phone in the normal way.
Ending a Call
Press the MFB once to end your call, or end the call via your mobile phone in the normal
way.
3. Press and hold the MFB until the headset’s status indicator flashes green and red
alternately.
4. Activate your mobile phone’s Bluetooth function. Please refer to your mobile phone
user guide for details.
5. Set the mobile phone to search for Bluetooth devices within the one metre range, as
instructed in the mobile phone user guide, and select “Arrow Lite-R” from the list.
6. Enter the pre-programmed passkey “0000” and press “OK” to pair your headset and
mobile phone. When the pairing is completed, the headset’s status indicator will flash
green rapidly for five times followed by a long beep.
7. Go back to your mobile phone’s main menu. For certain mobile phone models, once
the headset is activated, a headset icon will be shown on the screen. You should now
be able to make and receive calls using your headset.
IMPORTANT: If the pairing cannot be completed within two minutes after the pairing
mode has been activated, the headset’s status indicator will flash orange accompanied by
three beeps and will then turn off automatically. Please repeat steps 2 to 7 above to pair
the headset and the mobile phone again.
Adjusting the Volume
Press the volume UP or DOWN key repeatedly until you reach the desired volume level. The
volume may be affected by the volume setting of the caller’s phone as well. Re-adjust the
listening volume again when necessary.
Call Muting During Conversation
During conversation, press and hold the Volume Key for 2 seconds to mute the built in
microphone, when the mute function is activated, you will hear a short beep every 5 seconds
accompanied by the headset’s status indicator flashing every 5 seconds.
To cancel, press the Volume Key for 2 seconds to deactivate the muting function whilst in
conversation.
Dialing from Your Mobile Phone
Simply make calls on your mobile phone in the normal way.
Voice Dialing from Your Headset
If your mobile phone is equipped with the voice dialing function, simply press the MFB on
your headset, and when you hear a beep say the voice tag.
IMPORTANT: For voice dialing, you must record the voice tag (the person’s name) into your
mobile phone before using the voice dialing function on the Arrow Lite-R headset. Please
refer to your mobile phone’s user guide on how to record the voice tag.
Last Number Redialing from Your Headset
Press the MFB on your headset twice.
IMPORTANT: The above functions are only applicable to mobile phones with Bluetooth
Handsfree Profile. Functionality varies depending on the mobile phone model you have.
Please refer to your mobile phone user guide for additional information.
6
8 7
5