Impex CB-430 User Manual
Competitor bench cb-430, Model cb-430, Impex fitness products
Advertising
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
CB-430
Retain This
Manual for
Reference
07-03-03
OWNER'S
MANUAL
COMPETITOR BENCH
CB-430
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
Advertising
Table of contents
Document Outline
- BEFORE YOU BEGIN...................................................................................…. 1
- IMPORTANT SAFETY NOTICES..................................................................…. 2
- HARDWARE IDENTIFIER.....…....................................................................…. 3
- ASSEMBLY INSTRUCTIONS........................................................................…. 4
- EXPLODED DIAGRAM………………………………………………………………. 10
- PARTS LIST...............................................................................................……. 11
- WARRANTY.................................................................................................…. 12
- ORDERING PARTS.......................................................................................… 12
- ASSEMBLY INSTRUCTION
- Attach the bottom of Right Upright Beam (#3) to the Rear Stabilizer (#5). Attach the Right Upright Beam to the Cross Brace (#7).
- Secure the Right Upright Beam to the Rear Stabilizer with two M10 x 3 1/8” Carriage Bolts (#54), ( ¾” Washers (#64), and M10 Aircraft Nuts (#63).
- Secure the Right Upright Beam to the Cross Brace with two M10 x 2 ¾” Carriage Bolts (#56), one 4 ¾” x 2” Bracket (#27), two ( ¾” Washers (#64), and two M10 Aircraft Nuts (#63).
- Repeat Steps A, B, and C above to install the Left Upright Beam (#2).
- Insert the Left & Right Bar Holders (#23 & 24) into the selected holes on the Upright Beam.
- Attach the Cable (#17) to the opening on the top of the Lat Bar Frame (#1). Make sure the ball stopper of the Cable is underneath the Frame.
- Attach a Pulley (#29) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#57), two Ø 5/8” Pulley Bushings (#43), two ( ¾” Washers (#64), and one M10 Aircraft Nut (#63).
- Draw the Cable to the bracket on the top of Lat Bar Frame. Attach a Pulley to the bracket. Secure it with one M10 x 2” Allen Bolt (#55), one L-shaped Pulley Bracket (#28), two ( ¾” Washers (#64), and one M10 Aircraft Nut (#63).
- Pull the Cable down to the Sliding Weight Post (#11). Secure the Cable to the Post with one M10 x 1 3/8” Allen Bolt (#53), two ( ¾” Washers (#64), and one M10 Aircraft Nut (#63).
- Connect a Chain (#37) to the Lat Bar (#12) with a C-clip (#36). Connect the Chain to the Cable with another C-clip.
- Attach the Seat Support (#15) to the bracket on the Main Frame. Secure it with one M10 x 2 ½” Allen Bolt (#57), two ( ¾” Washers (#64), and one M10 Aircraft Nut (#63).
- Attach the holes on the Backrest Supports (#16) to the pivot on the Seat Support (#15). Attach the Backrest Board (#19) to the Backrest Supports (#16). Secure it with four M6 x 1 3/8” Hex Bolts (#58) and ( ½” Washers (#66).
- Place the Seat (#18) onto the Seat Support (#15). Secure it with four M6 x 5/8” Hex Bolts (#60) and ( ½” Washers (#66). Insert a L-shaped Pin (#40) into the hole on the Seat Support to lock the Seat and Backrest Board in position. Remove the Pin when f
- Attach the Arm Curl Pad (#20) to the Arm Curl Stand (#9). Secure it with two M8 x 5/8” Hex Bolts (#61) and ( 5/8” Washers (#65).
- Insert the Arm Curl Stand into the opening on the Main Frame. Secure it with a M10 Lock Knob (#33).
- PARTS LIST
- KEY NO. DESCRIPTION Q’ty