JVC RX-7022VSL - Manual (Page 40)

37
Operating Other Manufacturers’ Video Equipment
By changing the transmittable signals, you can use the remote
control supplied for this unit to operate other manufacturers’
equipment.
• Refer also to the manuals supplied for the other products.
• To operate these components with the remote control, first you
need to set the manufacturers’ code each for TV, CATV converter,
VCR and DVD player.
• After replacing batteries of the remote control, set the
manufacturers’ codes again.
To change the transmittable signals
for operating a TV
1 Press and hold TV .
2 Press TV/DBS.
3 Enter manufacturer’s codes using buttons 1 – 9,
and 0.
4 Release TV .
Now, you can perform the following operations on the TV.
TV : Turn on or off the TV.
TV/VIDEO : Set the input mode (either TV or VIDEO).
TV VOL +/– : Adjust the volume.
After pressing TV/DBS, you can perform the following
operations on the TV:
CH +/– : Change the channels.
1 – 9, 0, +10 (100+) : Select a channel.
10 : Function as the ENTER button.
Note:
Refer also to the manual supplied with your TV.
5 Try to operate your TV by pressing TV .
When your TV turns on or off, you have entered the correct
codes.
If there are more than one code listed for your brand of TV,
try each one until the correct one is entered.
Manufacturer Codes
JVC 00*, 02, 13, 14, 47, 74
AKAI 01, 02
BLAUPUNKT 03, 04
FISHER 01, 05
GRUNDIG 03, 06, 07
HITACHI 08, 09, 10, 49
IRADDIO 02
ITT/NOKIA 11, 12
LOEWE 06, 15, 16
MAGNAVOX 08, 17, 49
METS 50, 51, 52, 53
MITSUBISHI 08, 18, 19, 20
MIVAR 21
NORDMENDE 22, 23
OKANO 15
PANASONIC 24, 25, 26, 27, 76
PHILIPS 15, 17, 28, 75
QUELLE 52, 53, 54, 55, 56, 57, 58,
59, 60, 61, 62, 63, 64, 65,
66, 67
RCA/PROSCAN 08, 24, 29, 30, 31, 48
SABA 32, 33, 68, 69, 70
SAMSUNG 06, 08, 16, 34, 35, 49
SANYO 01, 05
SCHNEIDER 02, 15, 36
SHARP 37, 38, 77
SONY 39
TELEFUNKEN 40, 41, 42, 69
THOMSON 71, 72
TOSHIBA 37, 43, 44
ZENITH 45, 46
Manufacturers’ codes for TV
* “00” is the initial setting.
Manufacturers’ codes are subject to change without
notice. If they are changed, this remote control cannot
operate the equipment.
To change the transmittable signals for
operating a CATV converter or DBS tuner
1 Press and hold CATV/DBS .
2 Press CATV/DBS CONTROL.
3 Enter manufacturer’s codes using buttons 1 – 9,
and 0.
4 Release CATV/DBS .
Now, you can perform the following operations on the CATV
converter or DBS tuner.
CATV/DBS : Turn on or off the CATV converter or DBS tuner.
After pressing CATV/DBS CONTROL, you can perform the
following operations on the CATV converter or DBS tuner:
CH +/– : Change the channels.
1 – 9, 0, +10 (100+) : Select the channels.
10 : Function as the ENTER button.
Note:
Refer also to the manual supplied with your CATV converter or
DBS tuner.
EN30-42.RX-7020V[A]3 02.4.17, 5:16 PM 37