JVC RX-6022VSL - Manual (Page 13)

11
Selecting the Analog or Digital Input
Mode
When you have connected digital source components using both the
analog connections (see page 6) and the digital connections (see
page 7) methods, you need to select the input mode correctly.
1
Press one of the source selecting buttons—DVD,
TV SOUND, CD, or TAPE/CDR*—for which you
want to change the input mode.
Note:
* Among the sources listed above, you can select the digital input
only for the sources which you have selected the digital input
terminals for. (See “Setting the Digital Input (DIGITAL IN)
Terminals” on the left column.)
2
Select digital input mode.
On the front panel:
Press INPUT DIGITAL.
“DIGITAL AUTO” appears on the display and
the indicator for the detected signals also lights
up.
Ex: With the incoming signals of Linear PCM
To change the input mode back to analog
input,
press INPUT ANALOG.
“ANALOG” appears on the display and the
analog indicator also lights up.
Setting the Digital Input
[DIGITAL IN] Terminals
When you use the digital input terminals, register what components
are connected to which terminals (DIGITAL 1/2) so that the correct
source name will appear when you select the digital source.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step
1 again.
1
Press SETTING repeatedly until
“DIGITAL IN” appears on the display.
Then the display changes to show the current setting.
* “1DVD 2CD” is the initial setting. If you have already
changed the setting, another combination will be shown.
2
Press CONTROL UP
5/DOWN ∞ to
select the appropriate digital terminal
setting.
• Each time you press the button, the display
changes as follows:
1 DVD 2 CD j 1 DVD 2 TV j 1 DVD 2 CDR j
1 CD 2 DVD j 1 CD 2 TV j 1 CD 2 CDR j
1 TV 2 DVD j 1 TV 2 CD j 1 TV 2 CDR j
1 CDR 2 DVD
j 1 CDR 2 CD j 1 CDR 2 TV j
(back to the beginning)
Note:
When shipped from the factory, the DIGITAL IN terminals can be used
as the digital input for the following components:
–DIGITAL 1 (coaxial): For DVD player
–DIGITAL 2 (optical): For CD player
Basic Settings
Basic Operations / Basic Settings
Front Panel Remote Control
Display
Source
selecting
buttons
CONTROL
UP
5/DOWN ∞
ANALOG/
DIGITAL
SETTING
Remote
NOT
INPUT
DIGITAL
Source
selecting
buttons
SETTING INPUT
ANALOG
FM MODE
A/V CONTROL RECEIVER
AUDIO
TV
VCR
DVD
TEST
EFFECT
MENU
ENTER
RETURN
SOUND SLEEP
CENTER
REAR L
SUBWOOFER
CD–DISC REC PAUSE
TAPE/CDR CD DVD DVD MULTI
FM/AM
FM MODE
DIMMER TV/VIDEO SURROUND
ON/OFF
MODE
MUTING
VCR CH TV CH
VOLUME
TV SOUND VCR ANALOG /DIGITAL
REAR R
100
1
4
7/P
10
2
5
8
0
3
6
9
10
REMOTE CONTROL RM - SRX6020J
REW FF
TV VOLUME
STANDBY/ON
DVD DVD MULTI VCR TV SOUND ADJUST
RX-6020V AUDIO/VIDEO CONTROL RECEIVER
SETTING
MASTER VOLUME
CONTROL DOWN UP CD TAPE/CDR
SOURCE NAME
INPUT DIGITAL INPUT ANALOG
SPEAKERS ON/OFF SURROUND MODE
PHONES
SURROUND ON/OFF
FM/AM TUNING
STANDBY
FM/AM PRESET FM MODE
MEMORY
INPUT ATT
FM AM
STANDBY/ON
L C
LS RS CH- S
SPK PRO LOGIC ΙΙ DSP H.PHONE AUTO MUTING TUNED STEREO
VOLUME INPUT ATT SLEEP DIGITAL AUTO ANALOG
DIGITAL LINEAR PCM
R
S.WFR
CONTROL
DOWN UP
S.WFR
LS RS
CH-
S
LFE
DIGITAL 2 terminal setting
DIGITAL 1 terminal setting
TO BE CONTINUED ON THE NEXT PAGE
DVD DVD MULTI VCR TV SOUND
CD TAPE/CDR
SOURCE NAME
FM AM
TAPE/CDR CD DVD DVD MULTI
FM/AM TV SOUND VCR
On the front panel From the remote control
L
S.WFR
CH-
S
SPK
DIGITAL AUTO
LINEAR PCM
R
INPUT DIGITAL
INPUT ANALOG
INPUT ATT
EN08-17.RX-6020V/6022V[J]_f 3/4/02, 4:24 PM 11