JBL CVPD50 - Manual (Page 85)

85
able only through the remote’s menu sys-
tem being described in this section.
To avoid having the calibration settings
created with EzSet changed accidentally,
the remote allows you to disable the SPL
Select Button
9 on the remote. To
de-activate the button, follow these
steps:
1. Press and hold the Remote Menu
Button b for about 3 seconds
while the message shown in Figure
54 appears in the remote’s LCD
Information Display
2. Release
the button when the red light under
the Set Button s appears.
2. The remote’s MAIN MENU message
(Figure 55), will appear in the LCD dis-
play and the Set Button s will
remain illuminated in red. Press the
⁄ / ¤ Navigation Button q until
SET SPKR LEVELS appears on the
bottom line of the LCD screen, as
shown in Figure 104. Press the Set
Button s to enter the main EzSet
menu branch.
Figure 104
3. At the next menu screen (Figure 105)
press the ⁄ / ¤ Navigation Buttons
q once so that E
Z S ET DISABLE
appears in the lower line of the LCD
display.
Figure 105
4. Within 5 seconds, press the Set
Button s to disable the SPL
Select Button
9. Once the Set
Button s is pressed, the word
EXITING will flash four times in
the lower line of the LCD display
and then it will return to normal
operation.
Once these steps are completed, when
the SPL Select Button
9 is pressed,
the remote will show E Z S ET DISABLE
and it will not be activated.
To restore the EzSet feature to normal
operation, repeat the procedure outlined
above, except that in Step 3 you should
press the
⁄ / ¤ Navigation Button q
so that E Z S ET ENABLE appears in the
lower line of the LCD display. When that
display appears, press the Set Button
s and the EzSet feature will be reacti-
vated. You may then press the Remote
Menu Button
b to exit the remote’s
menu system and return to normal opera-
tion or press the Set Button s again
to immediately use the EzSet feature
to calibrate the system as shown
on page 51.
Renaming
While the names given to the buttons
and inputs on the remote represent rec-
ognizable categories of audio/video prod-
ucts, system operation may be easier if
the displays shown in the remote’s LCD
screen are customized to reflect the spe-
cific characteristics of a playback source’s
brand name or the new function given to
a specific button when one remote’s con-
trols are programmed into the remote.
The CVR700R2 remote allows you to
change the name of either a master
device or any button on the remote
using the following steps.
Renaming a Device
To rename a specific device/input source
button, follow these steps. For this exam-
ple, we will show you how to rename the
Device/Input Selector normally shown as
“TV” to “HDTV TUNER.”
1. Press and hold the Remote Menu
Button b for about 3 seconds
while the message shown in Figure
54 appears in the remote’s LCD
Information Display
2. Release
the button when the red light under
the Set Button s appears.
2. The remote’s MAIN MENU message
(Figure 55), will appear in the LCD dis-
play and the Set Button s will
remain illuminated in red. Press the
⁄ / ¤ Navigation Button q until
RENAME appears on the bottom
line of the LCD screen, as shown in
Figure 106.
Figure 106
3. Press the Set Button s and
RENAME DEVICE will appear on
the bottom line of the LCD screen, as
shown in Figure 107. Press the Set
Button q to begin renaming a
device.
Figure 107
4. The next display screen (Figure 108)
is where you select the device that
will be renamed. In our example, that
is the TV button. Press the
⁄ / ¤
Navigation Button q until the
name of the base device appears and
then press the Set Button s.
Figure 108
5. At the next menu screen, you will see
the device name on the bottom line of
the display with a blinking cursor box
to the right of the device name. Press
the
‹ Navigation Button q to
return the blinking cursor to the far
left side of the display line. You may
then retitle the device name as
shown in the next step.
6. To enter the new name, press the
Alpha Numeric Keys l. The let-
ters above the numbered buttons
indicate which letter or symbol will
appear when the button is pressed
during the renaming process. The first
press of the button will enter the first
letter shown, subsequent presses of
the same button will change the dis-
play to the other letters above that
numbered key. For example, since the
first letter we need to rename the
input to HDTV Tuner is an “H,” you
would locate the “H” above the “4”
button, and press the button twice.
The first press shows a “G,” the
second press changes it to an “H.”
Consult the table at the end of this
section to see which characters
pressing a particular button
generates.
7. After you enter the first letter of the
new device name, there are three
options for entering the next
character:
a. To enter a letter that requires a dif-
ferent numeric key to be pressed,
simply press that button. The cur-
sor will automatically move to the
next position and the first letter
accessed by the new button will
appear. Following our example, the
next letter needed is a “D,” so you
would press the “3” button once.
b. To enter a letter that uses the
same numeric key, you must first
press the
› Navigation Button
q to move the blinking cursor
block to the next position. Then
press the Numeric Key
l as
required to enter the desired letter.
c. To enter a blank space, press the ›
Navigation Button q twice.
The first press will move the cursor
to the right, and the second press
R E N A M E D E V I C E
T V
R E N A M E
R E N A M E D E V I C E
M A I N M E N U
R E N A M E
S E T S P K R L E V E L S
E
Z S E T D I S A B L E
M A I N M E N U
S E T S P K R L E V E L S
CVR700 OM 12/17/04 4:24 PM Page 85