Electrical connections, Лх¡‚¥¬„™и ‰шши, Ëõ¡µëõ·∫∫ª°µ – JVC GET0291-002A User Manual

Page 38: Μлх‡ж‘л¡‡µ‘¡‡¢è“°—∫хяª°√≥пх◊лπ, Хяª°√≥п¿“¬πх

Advertising
background image

2

ENGLISH

‰∑¬

ELECTRICAL CONNECTIONS

To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and
make all electrical connections before installing the unit.
Be sure to ground this unit to the car’s chassis again after installation.

Notes:
• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your

JVC car audio dealer.

• It is recommended to connect to the speakers with maximum power of more than 50 W (both at

the rear and at the front, with an impedance of 4

to 8 Ω). If the maximum power is less than

50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page 23 of
the INSTRUCTIONS).

• To prevent short-circuit, cover the terminals of the UNUSED

leads with insulating tape.

• The heat sink becomes very hot after use. Be

careful not to touch it when removing this unit.

A

Typical Connections /

°“√‡™◊ËÕ¡µËÕ·∫∫ª°µ‘

Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause
serious damage to this unit.
The leads of the power cord and those of the connector from the car body may be different in
color.

1

Connect the colored leads of the power cord in the order specified in the illustration below.

2

Connect the antenna cord.

3

Finally connect the wiring harness to the unit.

You can connect an amplifier and other equipment to upgrade your car stereo system.
• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so

that it can be controlled through this unit.

Disconnect the speakers from this unit, connect them to the amplifier. Leave the speaker

leads of this unit unused.

Connections Adding Other Equipment /

°“√µЛХ‡ж‘Л¡‡µ‘¡‡¢È“°—∫Хяª°√≥ПХ◊Лπ

Amplifier /

‡§√◊ËÕߢ¬“¬

B

*

3

Firmly attach the ground wire to the metallic body
or to the chassis of the car—to the place not
coated with paint (if coated with paint, remove the
paint before attaching the wire). Failure to do so
may cause damage to the unit.

*

3

µËÕ≈«¥“¬¥‘π„ÀÈ·πЛπ‡¢И“°—∫µ—«∂—Я‡А≈Б° А√◊Хµ—«∂—Я√∂

µ√ßË«π

∑’Л‰¡Л¡ ’’‡§≈◊Х∫ (А“°¡’’‡§≈◊Х∫Х¬ŸЛ „АИ¢Ÿ¥ ’ÕÕ°°ËÕπ

°ËÕπµËÕ≈«¥“¬¥‘π) À“°‰¡ËªØ‘∫—µ‘µ“¡§”·π–π”π’И

‡§√◊ЛХЯХ“®™”√я¥А√◊Х‡’¬А“¬‰¥

Heat sink

·ºËπ√–∫“¬§«“¡√ÈÕπ

CD Changer / ‡§√◊ËÕ߇≈Ëπ´’¥’ CD

Refer also to page 25 of the INSTRUCTIONS.

¥Ÿ¢ÈÕ·π–π”„πÀπÈ“

25

CAUTION /

¢ИХ§«√√–«—Я

• Before connecting the CD changer,

make sure that the unit is turned off.

°ЛХπ®–‡™◊ЛХ¡µЛХ‡§√◊ЛХЯ‡≈Лπ´’¥’ °√я≥“µ√«®

Х∫„АИ·πЛ„®«Л“‡§√◊ЛХЯ‡≈Лπ´’¥’π—Иπª‘¥Х¬

Connecting cord supplied for your CD changer

“¬µЛХ„АИ¡“ж√ИХ¡‡§√◊ЛХЯ‡≈Лπ´’¥

External Component /

Хяª°√≥П¿“¬πХ°

*

4

Line Input Adapter KS-U57 (not
supplied for this unit)

*

4

Õ·¥ª‡µХ√П “¬ —≠≠“≥‡¢И“

KS-U57

(

‰¡Л‰¥И„АИ¡“°—∫™я¥ª√–°Õ∫π’È)

KS-U57 *

4

°“√‡™◊ЛХ¡‚¥¬„™И ‰шшИ“

‡ж◊ËÕªÈÕß°—π°“√‡°‘¥‰шшИ“≈—¥«Я®√ ¢Х·π–π”„АИª≈¥¢—И«·∫µ‡µХ√’Л≈∫ХХ° ·≈И«®÷ßµËÕ“¬‰ø°ËÕ𵑥µ—ИЯ‡§√◊ЛХЯ

• µ√«® Х∫„АИ·πЛ „®«Л“‰¥И‡¥‘𠓬¥‘πµËÕ√–А«Л“Я‡§√◊ЛХЯ°—∫µ—«∂—ß √∂¬πµП „А¡Л·≈И«А≈—Я®“°µ‘¥µ—ИЯ

А¡“¬‡Аµя:

• „™Иж‘°—¥®”‡ж“–·∑πш‘« А“°ш‘«П¢“¥∫ЛХ¬ „АИª√ч°…“√И“ π¢“¬‡§√◊ЛХЯ‡’¬Я√∂¬πµП

JVC

• ¢Õ·π–π”„ÀȵËÕ≈”‚жЯ ∑’Л¡’°”≈—Я¢—∫Я я¥‡°‘π°«Ë“

50 W

(∑—ИЯ¥И“πÀπÈ“·≈–¥È“πА≈—Я ¡’§Л“§«“¡µИ“π∑“π

4

∂÷ß

8

)

∂И“°”≈—Я¢—∫µЛ”°«Л“

50 W

„Àȇª≈’ˬπ§Ë“

“AMP GAIN”

‡æ◊ËÕªÈÕß°—π‰¡Л„АИ≈”‚жЯ™”√я¥ (¥ŸÀπÈ“

23

§”·π–π”)

• °“√ªÈÕß°—π°“√≈—¥«ß®√ ®–µÈÕßæ—π¢—È« “¬µ–°—Л« ∑’Л‰¡Л„™И·≈И«¥И«¬‡∑ ªж—𠓬‰ø
• ·ºËπ√–∫“¬§«“¡√ÈÕπ®–√ИХπ¡“°А≈—Я®“°„™И √–¡—¥√–«—ЯХ¬Л“‰ª  —¡º—‡¡◊ЛХ∂Х¥™я¥ª√–°Õ∫π

°ЛХ•∑”°“•‡™•ЛХ¡µЛХ: µ•«®†Х•°“•‡¥‘•†“¬‰ш„•••¬•µПХ¬Л“Я•–¡—¥•–«—Х¬Л“„АИº‘¥ж•“¥„•°“•‡™•ЛХ¡µЛХ™я¥ª•–°Х•™я¥•’

°“•‡™•ЛХ¡µËÕº‘¥ж•“¥Х“®∑”„АИ‡°‘¥§«“¡‡ ’¬А“¬•И“¬·•Я°—•™я¥ª•–

°Х••’И‰¥И“•µ–°—Л«¢ХЯ†“¬‰ш ·•–¢ÕßÕÿª°••ÏµËÕ‡™•ËÕ¡®“°µ—«• Я••Х“®¡’†’∑’Л‰¡Л‡А¡•Х•°—•

1

µЛХ “¬‰ш’µ“¡≈”¥—∫∑’Л√–∫я„π√Ÿª¥È“π≈Л“Я

2

‡™◊ЛХ¡µЛХ°—∫“¬Х“°“»

3

 я¥∑И“¬ µËËÕ ò«π§«∫§ÿ¡°“√‡¥‘𠓬‰ш‡¢И“°—∫™я¥ª√–°Х∫™я¥π’И

§я≥“¡“√∂µЛХ°—∫·Х¡ж≈‘ш“¬‡ХХ√П · –Хяª°√≥ПХ◊тπК‰¥ф ‡ж◊ЛХ‡ж‘Л¡§я≥ ¿“ж‡ ’¬Я„АИ°—∫√–∫∫ ‡µХ√‘‚Х¢ХЯ√∂¬πµП

• µЛХ “¬µ–°—Ë«√–¬–‰°≈ ( ’πИ”‡Я‘π≈“¬¢“«) ‡¢È“°—∫ “¬µ–°—Ë«√–¬–‰°≈¢ÕßÕÿª°√≥ÏÕ◊Лπ К ‡ж◊ЛХ®– “¡“√∂§«∫§я¡‚¥¬™я¥ª√–°Õ∫π’И‰¥И
• ∂Х¥≈”‚жЯХХ°®“°™я¥ª√–°Õ∫π’И ·≈И«µЛХ‡¢И“°—∫‡§√◊ЛХЯ¢¬“¬ ∑‘ИЯ“¬µ–°—Л«≈”‚жЯ¢ХЯ™я¥ª√–°Õ∫π’И ‰«И

Rear speakers

≈”‚жЯА≈—Я

JVC Amplifier

‡§√◊ЛХЯ¢¬“¬‡’¬Я

JVC

Remote lead

“¬µ–°—Ë«•–¬–‰°•

Y-connector (not supplied for this unit)

¢ÈÕµËÕ√Ÿªµ—«

Y

(‰¡Л‰¥И„АИ¡“°—∫™я¥ª√–°Õ∫π’È)

Remote lead (Blue with white stripe)

“¬µ–°—Ë«•–¬–‰°• ( ’πИ”‡Я‘π≈“¬¢“«)

Signal cord (not supplied for this unit)

 “¬‡§‡∫‘≈ —≠≠“≥ (‰¡Л‰¥И„АИ¡“°—∫™я¥ª√–°Õ∫π’È)

KD-G456

Front speakers

≈”‚æßÀπÈ“

To the remote lead of other equipment or automatic
antenna if any

µËÕ “¬°—∫Хяª°√≥ПХ◊ЛπА√◊Х‡ “Х“°“»Х—µ‚π¡—µ‘∂È“¡’

KD-G456

JVC CD changer

‡§√◊ËÕ߇≈Ëπ´’¥’

JVC

L

R

L

R

L

R

L

R

KD-G456

CD changer jack

™ËÕ߇ ’¬∫µЛХ¢ХЯ‡§√◊ЛХЯ‡≈Лπ´’¥

CD

Signal cord (not supplied with this unit)

 “¬‡§‡∫‘≈ —≠≠“≥ (‰¡Л‰¥И„АИ¡“°—∫™я¥ª√–°Õ∫π’È)

External component

Хяª°√≥П¿“¬πХ°

To CD changer jack or another external component (see diagram

)

™ËÕ߇ ’¬∫µЛХ¢ХЯ‡§√◊ЛХЯ‡≈Лπ´’¥

CD

≈À–Хяª°√≥П¿“¬πХ° (¥Ÿ·ºπ¿Ÿ¡

)

Rear ground terminal

®я¥‡™◊ЛХ¡µЛХ “¬¥‘π¥È“πА≈—Я

Antenna terminal

¢—И« “¬Х“°“»

Line out
(see diagram

)

 “¬ÕÕ° (¥Ÿ·ºπ¿Ÿ¡

)

15 A fuse

ш‘« П¢π“¥

15 A

*

2

Before checking the operation of this unit prior to
installation, this lead must be connected, otherwise
power cannot be turned on.

*

2

°ËÕπ°“√µ√«®Х∫°“√∑”Я“π¢ХЯ™я¥ª√–°Õ∫π’È°ЛХπ∑’Л®–µ‘¥µ—Èß

µÈÕßµËÕ“¬µ–°—Ë«π’È°ËÕπ ¡‘©–π—Èπ®–‰¡“¡“√∂‡ª‘¥‡§√◊ËÕ߉¥

Black

 ’¥”

Yellow*

2

 ’‡А≈◊ХЯ

*

2

Red

 п‡‡¥Я

Blue with white stripe

 ’πИ”‡Я‘π≈“¬¢“«

*

1

Not included with this unit

*

1

‰¡Л‰¥И„АИ¡“°—∫™я¥ª√–°Õ∫π

Fuse block

·ºßø‘« 

Ignition switch

«‘∑™П®я¥√–‡∫‘¥

To metallic body or chassis of the car

µЛХ°—∫‚§√Я‚≈А–А√◊Х‡™´ ‘¢ХЯ√∂¬πµП

To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)

µЛХ°—∫¢—И«∑’Л¡’°√–·‰шшИ“„π·ºЯш‘«П ´÷ËßµËÕ°—∫·∫µ‡µХ√’Л√∂¬πµ (‚¥¬‰¡ËµÈÕß„™И« ‘∑™П®я¥√–‡∫‘¥)

(

12

‚«≈∑П§Я∑’Л)

To an accessory terminal in the fuse block

µЛХ°—∫¢—И« т«πª√–°Õ∫„π·ºßø‘«

To the remote lead of other equipment or automatic antenna if any (200 mA max.)

µËÕ “¬°—∫Хяª°√≥ПХ◊ЛπА√◊Х‡ “Х“°“»Х—µ‚π¡—µ‘∂È“¡’ (¢π“¥ ŸЯ я¥

200 mA

)

White with black stripe

 ¢“«·∂∫¥”

White

 ’¢“«

Gray with black stripe

 ’‡∑“·∂∫¥”

Gray

 ’‡∑“

Green with black stripe

 ’‡¢’¬«·∂∫¥”

Green

 ’‡¢’¬«

Purple with black stripe

 ’¡Л«Я·∂∫¥”

Purple

 ’¡Л«Я

Left speaker (front)

≈”‚жЯ´И“¬ (АπИ“)

Right speaker (front)

≈”‚æߢ«“ (ÀπÈ“)

Left speaker (rear)

≈”‚жЯ´И“¬ (А≈—Я)

Right speaker (rear)

≈”‚жЯ¢«“ (А≈—Я)

Instal1-2_KD-G456[UH]1.p65

10/25/04, 4:58 PM

2

Advertising
This manual is related to the following products: