JBL Professional WEM-1 - Manual (Page 5)

5
When using the WEM-1 to power surround speakers in
a home theater system:
In this application, the output level of your WEM-1 will not only be dependent
on the volume setting of your A/V source; it will also need to be properly
adjusted after installation and before use in order to be able to work correctly
with the other speakers in your multichannel surround system. To adjust the
output level, turn your A/V source on, set your A/V source’s volume control
about a third of the way up, and activate the speaker-level-adjustment test
tone. Make sure that the WEM-1 transmitter and receiver are on, both of the
speakers are connected, and there is RF lock (i.e., the LED on the receiver is
solid green). Using the remote control
1 and 2, adjust the volume level of
the WEM-1 until its output level is balanced with the rest of the speakers in your
surround system. From this point on, you will not be using the WEM-1 remote
control for volume settings. You will be increasing and decreasing the output level
for the entire surround sound system using your A/V source’s volume control.
Please note that the WEM-1 will retain its volume setting when it is in standby,
so there is no need to set its volume level every time the system is turned on.
Local Input
The JBL On Air WEM-1 receiver module also includes a local input on the front
of the receiver module. This input allows you to hook up a portable audio player
directly to the WEM-1, wherever you may happen to be. For example, you could
have the system connected to your audio receiver, listening to a local FM station,
and then hook up your portable music player to the local input, switching
between the two different sources.
To connect a portable audio player to the receiver module, simply connect the
preamp-out, line-out or headphone jack to the line-in on the front of the receiver
module using a 1/8-inch mini-jack – 1/8-inch mini-jack cable (not included).
To switch between the two sources, push the Input button 3 on the
remote control.
ID Codes
In the unlikely event that you experience interference when operating the
system, or if you have more than one set of WEM-1 transmitters and receivers
in operation, you may change the channel in which the system operates. On
both the transmitter and receiver modules, there is a four-position ID Code
selector
6B. Simply set each of the selectors to one of the other positions.
The transmitter and receiver must be set to the same position in order for the
system to function correctly. You can also set up a maximum of two receiver
modules to be receiving from the same transmitter by setting the channel
selector on the transmitter and the receiver to the same channel. Please
note that the two receiver modules need to be at least 10' (3m) apart, or
reception and operating range in one or both units may be degraded.
EQ Switch
The WEM-1 offers a choice of EQ positions for use with select JBL speakers.
This circuit optimizes the performance of the system when connected to the
loudspeakers indicated. If your specific loudspeaker is not listed below, simply
set the EQ Switch
C to position 1.
EQ Position Loudspeaker Model
1 No EQ; use with any loudspeaker not listed below
2 JBL CSB5
3 JBL CST55
4 JBL CS600 satellites
5 JBL CS400 satellites
6 JBL Control NOW, ™ JBL Control ® Monitor
Step 3.
Connect the speaker wire to the push terminals on the receiver module
A
and the terminals on the rear of your speakers, as shown in Figure 4. Please
note that the speaker wire features a polarity indicator to help distinguish its
two conductors. Use this polarity indicator to ensure that you are connecting
the positive (+) terminal on one speaker to the positive (+) terminal on the
other, and the negative (–) to the negative (–).
Figure 4.
Step 4.
Plug the transmitter module and receiver module into the wall outlets, using
the correct power supplies and power cords. Make sure the antennas
4E
are extended upward.
Make sure the ID Code setting on the transmitter 6 is set to the same setting
as that on the receiver B. See the “ID Codes” section for more information
on ID codes. When connected properly, the LED on the front of the receiver
should be red when first plugged in. When a button on the remote is pressed,
the LED should flash green until the transmitter and receiver “lock in.” It will
then light in solid green. This LED will light orange if the local input on the
receiver is selected (see the “Local Input” section for more details).
Adjusting the Volume
Depending on the type of connection and the specific source that you are
using, the volume setting on your audio receiver may affect the sound output
level of your WEM-1. To check whether the output from your source is volume-
dependent, turn the volume level on your audio receiver to approximately
halfway. Turn on your WEM-1 transmitter and receiver modules. Once the LED
on the receiver module lights in solid green, indicating that RF lock has been
achieved, verify that there is sound output from the speakers. Then increase
and decrease the volume control on your receiver and observe whether this
affects the sound output from your speakers. If it does not, then the volume
control on your source unit can be set at any position that you may desire,
as it does not affect the performance of the WEM-1. If changing the volume
setting on your source does affect the output from the WEM-1, then you will
need to always keep your source’s volume control at about halfway up with audio
receivers or A/V receivers. From this point on, you will use the remote control
included with the WEM-1 to adjust Volume
1 and 2.
Right Speaker Left Speaker
JBLP2744-WEM1-OM.qxd 10/29/08 2:42 PM Page 5