JVC XL-PR1BK - Manual (Page 6)

6
Program play
You can program up to 20 tracks in any desired order including
the same tracks.
1
During playback or in stop mode,
PROGRAM
2
Select the desired track.
3
PROGRAM
The track is registered.
4
Repeat steps 2 and 3 to program other tracks.
When you program exceeding 20 tracks, the program se-
quence number returns to “01” and will overwrite the previ-
ous setting.
5
The tracks are played in the programmed order.
• To confirm the program
In stop mode, press PROGRAM repeatedly. The programmed
track number will successively appear together with the pro-
gram sequence number. At this time, you can change the pro-
gram, if required.
If the programmed tracks are less than 20, track number “00”
appears for the youngest programmable sequence number, en-
abling further programming.
• To delete the entire program
Turn off the unit, or set the track number to 00 for the first pro-
gram sequencer number, “01”.
Program sequence
number
Track number to be programmed
00: Not programmed yet.
e.g. Track number 3
Repeat play
You can repeat one track or all tracks.
During playback,
MODE /
FM MODE
To cancel
Press MODE/FM MODE repeatedly until the repeat indicator
goes out.
Notes:
• You can also select Repeat play during Program play.
• You can also select Repeat play in stop mode.
Hyper-Bass Sound effect
You can enjoy powerful bass sound.
To get the Hyper-Bass Sound effect
Set HBS switch to “ON”.
OFF ON
HBS
To cancel
Set HBS switch to “OFF”.
Anti-Shock Protection
This function minimizes sound interruption caused by vibrations,
by utilizing audio data that has been stored in the memory ahead of
time (up to 45 seconds worth).
Normally, the “ANTI SHOCK” indicator lights up on the display
and the Anti-Shock Protection is in effect.
When the disc is played, as the audio data gradually stored in the
memory, the “ANTI SHOCK” indicator changes as follows:
To cancel
Press the A.S.P. button in stop mode or during playback.
The “ANTI SHOCK” indicator goes out.
To activate again
Press the A.S.P. button.
Notes:
• During Anti-Shock Protection operation, the disc rotates at a
higher rate than usual in order to collect extra audio data. This
may cause the batteries to run out faster and could result in a
slight increase in disc rotation noise.
• The Anti-Shock Protection function can be switched ON and
OFF during playback. However, this may cause a slight inter-
ruption in the sound because the disc’s rotational speed
changes.
[Fully stored]
ANTI SHOCK
indicator
ed
ve
Troubleshooting
(Repeatedly)
Next program sequence number
(Repeatedly)
Other Play Methods
Intro play
You can successively play the first 10 seconds of every track.
Intro play stops after playing the last track.
1
During playback,
MODE/
FM MODE
2
The Intro play will start from the first track.
To cancel
Press MODE/FM MODE repeatedly until “INTRO” goes out.
To normally play the track being played
Press 3/8 during Intro play.
Notes:
• In step 2, pressing ¢ instead of 3/8 will start Intro play from
the next track. Also, pressing 4 will start Intro play from the
current track. When no button is pressed, Intro play will start
from the next track after the current track has finished.
• You can also select Intro play in stop mode.
• You can also select Intro play during Program play.
Random play
You can play all tracks in a random order. After playing all tracks,
the unit stops.
During playback,
MODE /
FM MODE
To cancel
Press MODE/FM MODE until “RANDOM” goes out, or press 7
to stop.
Notes:
• You can also select Random play in stop mode.
• During Program play, you can not select Random play.
(Repeatedly)