JVC DR-M10 - Manual (Page 67)

Masterpage:Right-No-Heading
EN
67
Filename [DR-M10U_08Recording.fm]
Page 67 January 26, 2004 11:08 am
F
Enter the recording stop time.
Press w e to select “STOP”, then press rt repeatedly to
set the desired stop time.
● Each press of rt advances/goes back the stop time in 1-min.
increments.
● To advance/go back the stop time in 30-min. increments, press
and hold rt.
G
Enter the channel position.
Press w e to select “CH”, then press rt repeatedly to
select the desired channel.
H
Set “DAILY/WEEKLY” option.
Refer to step E in “VCR Plus+ ® Timer Programing”
(
੬
pg. 60).
● It is necessary to set “DAILY/WEEKLY” option for On-Disc
Timer Programing. (
੬
pg. 61, “Daily/Weekly Rec Function”)
I
Set the other recording options as required.
Refer to step E in “VCR Plus+ ® Timer Programing”
(
੬
pg. 60).
● You can select XP, SP, LP, EP or FR480 mode for “REC
MODE”. You cannot select FR (JUST), FR60–FR360 and
FR420.
J
Access the confirmation screen.
Press ENTER.
K
Complete timer programing.
Press ENTER.
● To program another timer, repeat steps B – K.
To timer-record the program with the
programed disc
A
Load the disc.
A Press x to open the disc tray.
B Place the programed disc on the disc tray.
● For details, refer to “Placing a Disc” ( ੬
pg. 11).
C Press x to close the disc tray.
B
Engage the unit’s timer mode.
Press DVD 1. The unit turns off and “ ” appears
on the front display panel.
● To disengage the timer mode, press DVD 1 again.
NOTES:
● Even if On-Disc Timer Programing is overlapping with other
timer programing, any caution message does not appear. In
such a case, recording will be executed in the descending
order of the recording start time of the program.
● On-Disc Timer Programing is not possible on a DVD-RW disc
formatted in video mode. (
੬
pg. 101, “Format a DVD-RW
disc”)
● The information of a program recorded with On-Disc Timer
Programing is not stored in the library. (
੬
pg. 82)
● The play list is not created for the programs recorded with On-
Disc Timer Programing. (
੬
pg. 78)
● VCR Plus+ Timer Programing is not possible on the discs used
exclusively for On-Disc Timer Programing.
● Manual Timer Programing is not possible on the On-Disc
Timer Programed disc. (
੬
pg. 64)
● Basic Recording is not possible on the On-Disc Timer
Programed disc. (
੬
pg. 57)
● The On-Disc Timer Programing function does not work on the
unit form other manufactures even if the On-Disc Timer
Programed disc is loaded.
● The beginning of a program may not be recorded. Also, if the
1st program’s recording stop time and the 2nd program’s
recording start time is the same, the ending of the 1st program
may not be recorded.
● If there is a power cut while recording, the recordings before
the power cut are not guaranteed. Cable Box or DBS Receiver Users
To timer-record a satellite broadcast using the On-Disc Timer
Programing function:
A Perform “Cable Box Control Setting” (
੬
pg. 29) or “DBS
Receiver Control Setting” (
੬
pg. 32).
B Perform “On-Disc Timer Programing”.
C Leave the Cable Box or DBS receiver’s power on.
DR-M10U_08Recording.fm Page 67 Monday, January 26, 2004 11:08 AM