JVC GD-V4200PCE-G - Manual (Page 15)

15
ENGLISH
C O N T R A S T
B R I G H T
C H R O M A
P H A S E
S H A R P N E S S
s u b m e n u
r e s e t
A D J U S T :
P I C T U R E A D J .
S E L E C T : E X I T : M E N U
V I D E O A
: + 0 1
:
: – 0 2
:
:
0 0
0 0
0 0
S I Z E / P O S I T I O N A D J .
P I C T U R E A D J .
F U N C T I O N S E L E C T
S T A T U S D I S P L A Y
E N T E R :
M A I N M E N U
S E L E C T : E X I T : M E N U
This item
appears only
when the
“RGB” input is
selected. Cursor ( 3 )
5
Press 2/3 to adjust the selected item.
6
Press MENU/EXIT (or MENU on the
Monitor) twice to exit from the menu
operations.
To make an adjustment while viewing the adjustment
bar
After step 3 on page 14, proceed as follows:
1 Press 5/∞ to move the cursor (3) to “sub menu.”
2 Press 3 to display the Sub Menu.
The Sub Menu for H SIZE appears on the screen.
3 Press 5/∞ to select the Sub Menu you want to adjust.
Each time you press the button, the Sub Menu changes as
follows:
4 Press 2/3 to adjust the selected item.
5 Repeat steps 3 and 4 to adjust the other items.
6 Press MENU/EXIT (or MENU on the Monitor) three times
to exit from the menu operations.
To reset the adjustments
After step 3 on page 14, proceed as follows:
1 Press 5/∞ to move the cursor (3) to “reset.”
2 Press 3.
The confirmation screen appears.
3 Press 3 again to reset the adjustments.
To cancel the reset, press MENU/EXIT (or MENU on the
Monitor).
Note:
• Adjustment values for both horizontal and vertical sizes of
the screen are so related that if one is adjusted up to near
the maximum value, the attainable value of the other will
be decreased.
: + 0 1 H S I Z E
+ + + +
H SIZE H POSITION
V POSITION CLOCK PHASE
V SIZE
A r e y o u s u r e ?
" Y E S " t h e n p r e s s k e y .
" N O " t h e n p r e s s k e y
M E N U
r e s e t
Adjusting the Picture Quality
Picture quality can be set for each input mode.
1
Press MENU/EXIT (or MENU on the
Monitor) to display the Main Menu.
2
Press 5/∞ to move the cursor (3) to
“PICTURE ADJ.”
3
Press 3 to display the Picture
Adjustment Menu.
4
Press 5/∞ to move the cursor (3) to the
item you want to adjust.
Item Adjustment range
CONTRAST –20 to +20
BRIGHT (brightness) –20 to +20
CHROMA* –20 to +20
PHASE** –20 to +20
SHARPNESS –20 to +20
sub menu See “To make an adjustment
while viewing the adjustment
bar” on the next page.
reset See “To reset the adjustments” on
the next page.
* Adjustment is not possible when RGB input is selected.
** Adjustment is only possible when viewing NTSC signal
through the VIDEO A or B terminal.
5
Press 2/3 to make adjustments.
6
Press MENU/EXIT (or MENU on the
Monitor) twice to exit from the menu
operations.
12-19.GD-V4200PZW-A[EN]/f 00.2.23, 5:21 PM 15