JVC BR-DV600UA - Manual (Page 8)

12
3-1 Video system connections
3 CONNECTIONS
Connecting a monitor
The on-screen display can be viewed on a monitor
connected to the [VIDEO MONITOR OUT] connector.
Connecting video equipment
Connect the video device to the appropriate connector
(4 types are available).
Outputs
5 Analog outputs
Composite signal : [LINE OUT] connector (BNC)
Component signal (Y/B-Y/R-Y) : [COMPONENT OUT]
connectors (BNC x 3)
YC signal : [Y/C OUT] connector (4-pin)
5 Digital output
Digital video signal (conforming to IEEE 1394)
[DV IN/OUT] connector
Inputs
Select input video signals with the front panel’s [VIDEO
INPUT] switch or the No. 108 <VIDEO INPUT SELECT>
menu switch.
5 Analog inputs
Composite signal : [LINE IN] connector (BNC)
Component signal (Y/B-Y/R-Y) : [COMPONENT IN]
connector (BNC x 3)
YC signal : [Y/C IN] connector (4-pin)
5 Digital input
Digital video signal
: [DV IN/OUT] connector
(conforming to IEEE 1394)
Reference sync signal
This unit automatically selects the sync signal as shown in
the table below, depending on the presence of external sync
input (SYNC IN) and video input (VIDEO IN), the No. 003
<SYNC SELECT> menu switch setting and operation mode.
When IEEE 1394 input is selected, “INT” is selected
regardless of the setting. When the No. 108 <VIDEO
INPUT SELECT> menu switch is set to “COMPONENT”,
the operation is the same as that performed with the No.
003 <SYNC SELECT> menu switch set to “AUTO”
regardless of the setting.
Note:
• When search pictures or low-quality video signals
are input, temporary distortion of picture or sound
may occur. Clean up the signals with a TBC or
other processing device before inputting.
DC 12V
PGZ01945
TIMER TIME CODE
COMPONENT VIDEO
SYNC IN
REC OFF PLAY
DV IN/OUT
REMOTE
AUDIO
2 1
SERIAL
CH 1/3
OUT
OUT
IN
IN B-Y IN Y/C
LINE
OUT
OUT MONITOR
CH 2/4
MONITOR OUT
R-Y Y
IN OUT
Y/C
Input
Y/C DV
Component DV
Composite
Composite Component
Output
Video input to a VCR, etc.
Composite
Monitor TV
External sync signal
Video output from a VCR, etc. Sync signal generator, etc.
SYNC IN No Yes No Yes
VIDEO IN No No Yes Yes
EXTERNAL Playback INT EXT INT EXT
Recording INT INT VIDEO VIDEO
AUTO Playback INT EXT VIDEO EXT
Recording INT INT VIDEO VIDEO
INT: Internal sync EXT: External sync VIDEO: Video sync
• The phase of the output signal cannot be adjusted
for external sync signals. The sub carrier cannot be
locked.
• Plugging and unplugging the external sync or video
signal connector during operation causes distortion
in the picture and sound for about 10 seconds.
• When signals input from the composite connector
are output from the component connector, color may
disappear in some parts of the left section of the
monitor screen. This is not a malfunction.
• The set up is not applied to signals input to the
[DV IN/OUT] connector and output in EE mode
(component, Y/C, composite). Input signals are
recorded as is.
• Use a video signal of less than 1 V(p-p) such as a
black burst signal for external sync signal.
• When video signals are input to the DV IN/OUT
connector, distortion may occur in the lower section
of the picture in the EE mode. However, recording
is performed normally.
• When the No. 003 <SYNC SELECT> menu switch is
set to “EXTERNAL” and no signal is input to the
[SYNC IN] connector, noise may appear in the
playback picture. This is not a malfunction.
Notes:
13
DC 12V
PGZ01945
TIMER TIME CODE
COMPONENT VIDEO
SYNC IN
REC OFF PLAY
DV IN/OUT
REMOTE
AUDIO
2 1
SERIAL
CH 1/3
OUT
OUT
IN
IN B-Y IN
Y/C
LINE
OUT
OUT MONITOR
CH 2/4
MONITOR OUT
R-Y Y
IN OUT
3 CONNECTIONS
Audio output from a VCR, etc.
Audio input to a VCR, etc.
DV
Mic
Headphones
DV
Analog audio
(2 channels) Analog audio
(monaural)
Analog audio (2 channels)
Connection with a monitor TV
The audio output from the [AUDIO MONITOR OUT] connector
is monaural.
Use the front panel [AUDIO MONITOR] switch or No. 211
<AUDIO MONITOR> menu switch to select the audio channels
you want to monitor. The selected audio channel is shown in
the table below. Adjust the audio volume level on the monitor.
੬ See “Playback preparation” on page 28.
Headphones jack
Audio can be monitored in stereo using the headphones.
Use the front panel [AUDIO OUTPUT] switch to select the
audio channels you want to monitor. The selected audio
channel is shown in the table below. Adjust the audio volume
level with the front panel [PHONES] control.
Inputs
5 Analog inputs
Audio connectors (CH1/3, CH2/4)
Analog input connectors are only provided for 2 channels. It is
not possible to record 4 channels simultaneously. Audio input
from each connector is normally recorded on the CH1 and CH2
channels. Recording on the CH3 and CH4 can be performed
in the Audio Dubbing mode with the No. 245 <SAMPLING
RATE> menu switch set to “32K”.
For audio dubbing, refer to “Audio dubbing” on page 27.
5 Digital inputs
Digital signals conforming to IEEE 1394 can be input to the
[DV IN/OUT] connector. In this case, the audio recording level
cannot be adjusted. When audio signals are input to the [DV
IN/OUT] connector, some noise will occur at the point where
recording ends. To reduce this noise during playback, set the
No. 214 <V. FADE> menu switch to “ON”.
5 Mic input jack
Connect a monaural microphone. The same audio is recorded
on both channels.
Outputs
5 Analog outputs
Audio connectors (CH1/3, CH2/4)
Analog output connectors are provided for 2 channels. For
MiniDV format, use the front panel [AUDIO OUTPUT] switch to
select for 4-channel audio. The selected audio channel is
shown in the table below.
੬ See “Playback preparation” on page 28.
5 Digital outputs
Digital signals conforming to IEEE 1394 are output from the
[DV IN/OUT] connector.
Relationship between [AUDIO OUTPUT] / [AUDIO MONITOR]
switch and audio output channel
(During playback with 32 kHz sampling, audio dubbing, and
DV input with the 32 kHz sampling in the EE mode)
Regardless of setting of this switch, CH1/2 is selected for
ordinary recording, record pause and analog audio input in the
EE mode. CH3/4 is selected for audio dubbing in the Pause
mode.
With the No. 054 <SLIDE SW FUNCTION> menu switch set to
“AUDIO”.
Monitor TV
CH1 CH1 CH2
CH1/3 CH1/3 CH2/4
CH3 CH3 CH4
CH1/2 CH1 CH2
CH1/2/3/4 CH1/3 CH2/4
CH3/4 CH3 CH4
CH2 CH1 CH2
CH2/4 CH1/3 CH2/4
CH4 CH3 CH4
R
L
MIX
CH1/2
MIX
CH3/4
CH1/2
MIX
CH3/4
CH1/2
MIX
CH3/4
AUDIO switch Connector
MONITOR OUTPUT MONITOR OUT
AUDIO OUT
CH1/3 CH2/4
3-2 Audio system connections