JVC DR-MX1S - Manual (Page 51)

Masterpage:Right+
EN
51
Filename [MX1SEU_10Timer Recording.fm]
TIMER RECORDING ON HDD/DVD DECK
Page 51Monday, 6 December 2004 14:01
You can programme this unit to timer-record as many as 16
programmes.
If you do not know the
a number for the programme you
wish to record, use the following procedure to set your unit to
timer-record the programme.
1
Load a recordable disc if recording to DVD.
2
Press PROGRAMME to access the programme top screen.
3
Press FGD E to select ACALENDAR PR.B, then press ENTER.
● When APROGRAMME FULL DELETE UNWANTED TIMER
PROGRAMMES B appears on the TV screen, you need to
cancel some of the reserved programmes. (A pg. 52)
4
Press FGD E to select the desired date, then press ENTER.
5
Press F G to select ARECORD
TO B, then press ENTER. Press
F G to select the desired
recording deck, then press
ENTER.
6
Press F G to select ASTARTB,
then press ENTER. Press F G
to set the desired start time,
then press ENTER.
● Each press of F G increases/decreases the start time in 1-
minute interval.
● To increase/decrease the start time in 30-minutes interval,
press and hold
F G.
7
Press F G to select ASTOPB, then press ENTER. Press F G to
set the desired stop time, then press ENTER.
● Each press of F G increases/decreases the stop time in 1-
minute interval.
● To increase/decrease the stop time in 30-minutes interval,
press and hold
F G.
8
Press F G to select ATV PROGB, then press ENTER. Press
F G to select the desired channel.
9
Press F G to select ACONFIRMB, then press ENTER.
10
Set the other recording options as required.
● Refer to step 8 in Ac Timer ProgrammingB (A pg. 49).
11
Press F G to select AOKB,
then press ENTER to access
the Programme Confirmation
screen.
12
Press D E to select AEXITB,
then press ENTER to
complete timer
programming.
● To programme another timer,
press
D E to select ACONTINUEB, then press ENTER.
● If APROGRAMME OVERLAPPEDB appears on the TV screen,
delete or modify the programmes.
NOTES:
● When two successive programmes are recorded on a DVD-RW
disc with Manual Timer Programming function, the beginning of
the second one may be left off the recording.
● If the copy limited programme is received during timer-recording,
the unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you
programmed.
Manual Timer Programming
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
rtwe
PROGRAMME
ENTER
AUX
CABLE/SAT
DVD TV
BBC1
[MISC. ] XP
BBC1
23:00
22:30
HDD
[0]: SAT
2
ENTER
SELECT
PROGRAMME
EXIT
PROGRAMME > CALENDAR PR. (2/3)
PRESS [PROGRAMME]
TO EXIT
SELECT WITH @
THEN PRESS [ENTER]
CONFIRM
14/01/04 WED 22:30 - 23:00
RECORD TO
STOP
START
TV PROG
Satellite Receiver Users
To timer-record a satellite broadcast using Manual Timer
Programming:
A Perform ASatellite Receiver Control Setting (HDD & DVD
Deck Only) B (A pg. 22).
B Perform AManual Timer ProgrammingB (A pg. 51).
In step 8, press AUX to change ATV PROGB to ASATB. Then
press F G to enter the channel position for the satellite
broadcast.
C Leave the satellite receiver’s power on.
Relief Recording
When a programme that is set for the DVD deck cannot be
recorded properly, the programme is recorded to the HDD deck
instead in XP mode.
● If the remaining capacity of the hard disc is not sufficient, the
programme is recorded to the DVD deck until the remaining
capacity of the DVD disc lasts.
● If AJUSTB is selected for the recording mode, the current
recording mode for the DVD deck is applied.
BBC1
1:00 28:00
2
ENTER
SELECT
PROGRAMME
EXIT
PROGRAMME > CALENDAR PR. (3/3)
PRESS [PROGRAMME]
TO EXIT
SELECT WITH @
THEN PRESS [ENTER]
OK
INPUT TITLE
CATEGORY
VPS/PDC
WEEKLY/DAILY
REC MODE
GARDENING
EDUCATION
OFF
MON-FRI (FOR A WEEK)
FR360
14/01/04 WED 22:30 - 23:00
GARDENING
[EDUCATION] FR360
MX1SEU_00.book Page 51 Monday, December 6, 2004 2:01 PM