JVC DR-M150SEK - Manual (Page 38)

Filename [M150SEK_07Timer Recording.fm]
Masterpage:Left+
38
EN
TIMER RECORDING
You can programme this unit to timer record as many as
8 programmes up to 30 days in advance. To perform normal timer
programming without using EPG, use the following procedure to
set your unit to timer record the programme.
1
Load a recordable disc.
● For details, refer to APlacing A DiscB (A pg. 9).
2
Press PROG to display
the
APROGRAMME
CHECK B screen.
● When 8 timer
programmes appear on
the TV screen, you need
to cancel some of the
reserved programmes.
3
Press selection keys
repeatedly to select
ANEW TIMER
PROGRAMME
B, then
press ENTER.
4
Press selection keys to
set the desired date
(
ADATEB), then press E.
5
Press selection keys to
set the desired start
time (
ASTARTB), then press E.
● Each press of F G increases/decreases the start time in
1 minute interval.
● To increase/decrease the start time in 30 minutes interval,
press and hold
F G.
6
Press selection keys to set the desired stop time ( ASTOPB),
then press E.
● Each press of F G increases/decreases the stop time in
1 minute interval.
● To increase/decrease the stop time in 30 minutes interval, press
and hold
F G.
7
Press selection keys to set the desired channel ( ATV PROGB),
then press E.
8
Set the other recording options as required.
9
Press ENTER to access the Programme Confirmation screen.
10
Press ENTER to complete the timer programming.
● To programme another timer, repeat steps 2 - 10.
11
Press TIMER j to engage the unit’s timer mode.
● The unit turns off automatically and j appears on the front
display panel.
● To disengage the timer mode, press TIMER j again.
NOTES:
● When two successive programmes are recorded with the
AManual Timer ProgrammingB function, the ending of the first
programme or the beginning of the second programme may not
be recorded.
● If the copy limited programme is received during timer recording,
the unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you
programmed.
Manual Timer Programming
ATTENTION:
If timer programming cannot be set or cancelled, wait for about
40 seconds and then try again.
● Turn on the unit.
● Turn on the TV and select an input mode such as EXT1.
● Make sure that the unit’s built-in clock is set properly.
● Slide the TV/DVD switch to DVD.
PROG
(FGDE)
ENTER
TIMER j
AUX
DVD TV
Selection Keys
19:00 - 20:00
22:00 - 22:30
13:30 - 14:00
16:00 - 17:00
BBCi 51
BBC 40
CBBC 30
BBC 1
PROG
PROGRAMME CHECK
++++++++++++++++++ NEW TIMER PROGRAMME ++++++++++++++++++
DISC TIMER PRGM
SELECT WITH [CURSORS]
THEN PRESS [ENTER] OK
SELECT
EXIT
05/07 SAT SP
10/07 THU XP
11/07 FRI LP
WEEKLY
11/07 FRI LP
DATE START TV PROG REC MODE DAILY/WEEKLY STOP
LP
VTM 10 20:30 20:00
TIMER PROGRAMME
DATE START STOP TV PROG
05/07 SAT
DAILY/WEEKLY
NAME
SET TIMER PROGRAMMING WITH [CURSORS]
THEN PRESS [ENTER]
REC MODE
CONFIRM
SELECT PROG
EXIT
Satellite Receiver Users
To record a satellite broadcast using Manual Timer
Programming:
A Perform Manual Timer Programming.
● In step 7, press AUX to set ATV PROGB to ASATB. Then press
F G to enter the channel position for the satellite broadcast.
B Set the satellite receiver to the appropriate channel for
recording.
● Leave the satellite receiver’s power on.
M150SEK_00.book Page 38 Wednesday, June 15, 2005 4:04 PM