JVC SP-XCA75 - Manual (Page 68)

64
Operating other manufacturers’ VCR
Manufacturers’ codes for VCR
Manufacturer Code
JVC 01
Aiwa 02, 20
Bell+Howell 03, 16
Blaupunkt 04
CGM 03, 05, 16
Daewoo 34
Digtal 05
Fisher 03, 16
G.E. 06
Grundig 07
Hitachi 08, 09
Loewe 05, 10, 11
Magnavox 04, 05
Mitsubishi 12 – 15
Manufacturer Code
Nokia 16
Nordmende 17 – 19, 31
Orion 20
Panasonic 21
Philips 05, 22
Phonola 05
Saba 17 – 19, 23, 31
Samsung 24, 25
Sanyo 03, 16
Sharp 26, 27
Siemens 07
Sony 28 – 30, 35
Telefunken 17 – 19, 31, 32
Toshiba 33
* Manufacturers’ codes
are subject to change
without notice. If they
are changed, this
remote control cannot
operate the
equipment.
By changing the remote control signals from preset ones to
the other manufacturers’, you can use the remote control
supplied for this system to operate other manufacturers’
VCRs.
• You can also operate other manufacturers’ TVs using the
remote control supplied with this system. (See page 16.)
• When operating other manufacturers’ VCR, aim the remote
control directly at the remote control sensor on the VCR.
Refer also to the instruction manuals supplied with the
VCR.
RM–STHA75R
DVD CINEMA SYSTEM
CHANNEL/ZOOM VOLUME TV VOL
TUNING
STOP
DIMMER
PAUSE
FF/ /REW
TV/VIDEO
1
MUTING
¡
REC
PLAY
DOWN UP
MEMORY STROBE
DVD VCR 1
AUDIO
VIDEO/
TV SOUND
ANGLE
FM/AM
SUBTITLE DECODE
RETURN DIGEST
VFP
TOP MENU MENU
CONTROL EFFECT
S.WFR TEST
SLEEP
TV
VCR
SETTING
TV RETURN
ENTER
ON
SCREEN
CHOICE
FM MODE
1 2 3
4 5 6
7 8 9
10 0 +10
100+
TV AUDIO
VCR
SOUND
PTY SEARCH
DVD
RDS
TA/NEWS/INFO
PTY ( PTY 9
RDS DISPLAY
SURROUND OFF DSP
CENTER
–
+
–
+
–
+
–
+
SURR-L SURR-R S-BACK –
+
ADJUST
O.T.
REPLAY
7 Setting the transmittable signal for your
VCR
• You can operate a JVC VCR without setting the remote
control signal.
1 Set the remote control mode selector to
“DVD.”
2 Press and hold VCR .
Keep it pressed up to step 5.
3 Press VCR CONTROL.
4 Press the number buttons (1–9, 0) to enter
a manufacturer’s code (2 digit).
See the list below to find the code.
Ex.: For a Siemens VCR, press 0, then 7.
For a Panasonic VCR, press 2, then 1.
5 Release VCR .
6 Try to operate your VCR by pressing
VCR .
When your VCR turns on or off, you have entered the
correct code.
If more than one cord is listed for your brand of VCR, try
each one until you enter the correct one.
After setting transmittable signals, you can use the
following buttons for the VCR operations.
VCR :Turns the VCR on and off.
After pressing VCR CONTROL:
PLAY :Starts playback.
STOP :Stops operation.
PAUSE :Pauses playback.
¡ :Fast forwards a video tape.
1 :Rewinds a video tape.
÷ REC :Starts recording by pressing with PLAY.
Pauses recording by pressing with PAUSE.
CHANNEL +/–:Changes the TV channels on the VCR.
Maintenance
Set the remote
control mode
selector to “DVD.”
EN64-70.TH-A75R[B]_f 02.9.5, 4:15 PM 64